Henden H62SP Скачать руководство пользователя страница 7

Henden 6 Star 2 Speed Pump Installation & Owners Manual

4. LOW ENERGY OPERATION

Your Henden 2 Speed Pump has 2 speed settings:
1.  Eco Flow – Lowest Speed
2.  High Flow – Highest Speed
 Eco Flow mode provides the lowest speed and therefore 
the greatest energy savings.

Recommended Speed settings for your pool

Operation

Recommended  

Speed Settings

Pool Filtration

Eco Flow

Automatic pool cleaner operation

High Flow

Backwashing your media filter
Manually cleaning your pool
Water Feature operation
Spa Jet operation
Solar pool heating

Guidelines for recommended pump operating hours:
Australian Standards AS3633: “Private swimming pools 
- water quality” states that “the minimum turnover rate 
shall be a single turnover of the full volume of the pool 
water, within the period that the pump would normally be 
operating...”
The table below provides a guide to the running times of 
your pump while in filtration mode in order to achieve the 
minimum turn over rate:

Pool Size (Litres)

Speed Setting (hours)

Eco Flow

High Flow

20,000

2.3

1.2

30,000

3.5

1.8

40,000

4.7

2.4

50,000

5.9

3.0

60,000

7.0

3.6

80,000

9.4

4.7

100,000

11.7

5.9

4.1 Using your Henden 2 Speed pump with a 

Henden Salt Water Chlorinator

Chlorinators require a minimum flow rate through the 
chlorinator cell for best efficiency and cell life. If you are 
using this pump with a Henden Chlorinator please ensure the 
flow rate is sufficient to cover your cell plates completely at 
all times of operation. For other chlorinators please refer to 
the relevant installation and operating instructions.

Henden 6 Star 2 Speed pump 

Hydraulc Performance Chart

4.2 Operating your automatic pool cleaner

Before installing or purchasing a pool cleaner for use with 
your Henden 2 Speed Pump, it is important to know the 
minimum flow rates required for it to operate effectively.

4.3 To operate a suction pool cleaner with your 

Henden 2 Speed Pump

1.  Activate the High Flow setting and allow the pump to 

fully prime by running for 2 minutes. You will know 
the pump is primed when you can see a strong flow of 
water through the clear leaf basket lid.

2.  When all air is expelled from the leaf basket, connect 

the pool cleaner hose firmly into the skimmer plate or 
dedicated wall suction. 

3.  The cleaner should only be connected for as long as 

is required to clean the surface of your pool. When 
cleaning is complete, disconnect the cleaner and 
remove the skimmer plate from the skimmer box. 

4.  Reactivate the most efficient speed setting for daily 

filtration. The Eco Flow setting is recommended.

NOTE: To achieve optimum energy 
efficiency from your Henden 2 
Speed Pump. DO NOT keep the 
automatic pool cleaner connected 
when cleaning is not required.

 

HENDEN

 INSTALLATION & OWNERS MANUAL 

|

 

7

25

TOTAL HEAD (m)

20

15

10

5

0

0

100

200

300

FLOW (lpm)

400

600

500

1450rpm

2850rpm

Содержание H62SP













Отзывы: