Henden H62SP Скачать руководство пользователя страница 4

Henden 6 Star 2 Speed Pump Installation & Owners Manual

4

 

|

 

HENDEN

 INSTALLATION & OWNERS MANUAL

INTRODUCTION

Congratulations on your purchase of a quality product from 
the Henden range of pool and spa equipment. You can be 
assured to experience many years of reliable and super-
efficient performance from your Henden 2 Speed Pump.
Read these instructions in their entirety before switching 
on this pump. If you are uncertain as to any of these 
installation and operating instructions please contact 
Henden as listed on the back of this document.
The Henden 2 Speed Pump has been designed to circulate 
swimming pool and spa water in conditions set out in 
the Australian Standard for swimming pool water quality 
AS 3633 or equivalent. They should not be used for any 
other purpose without first consulting your local Reece 
Irrigation & Pools branch or 1300 HENDEN.
Every Henden 2 Speed Pump is thoroughly water tested 
against a number of flow, pressure, voltage, current and 
mechanical performance parameters.
Henden’s advanced pump manufacturing technology 
provides reliable and efficient pumping performance that 
lasts and lasts.

INSTALLATION

1. INSTALLATION OF THE HENDEN  

2 SPEED PUMP

1.1 Location of the Pump

The pump should be located as close to the water as 
possible and mounted on a firm base in a well drained 
position, high enough to prevent any flooding. The pump 
position should also allow easy access for servicing so 
that the product nameplate can be easily read.

1.2 Weather Protection

It is strongly recommended that the pump is protected 
from the weather. Enclosures should be ventilated to 
prevent condensation build-up and allow a free flow of air 
for the fan cooled motor.

1.3 Power Connection

The Henden 2 Speed Pump is suitable for connection to a 
nominal 220-240 volt 50Hz power supply and is equipped 
with a flex and 3 pin plug. If a power outlet is not available 
within 3 metres of the pump, a 3 pin power point in a 
safe, dry place may need to be provided by an electrician. 
Extension cords are unsafe around pools and should be 
avoided. If the supply cord of this product is damaged it 
must be replaced by Henden or the manufacturer, with 
genuine Henden spares.
This Henden 2 Speed Pump incorporates motor overload 
detection designed to protect the motor from overheating. 
If the motor gets too hot during operation, it’s operating 
speed will reduce to bring it to an acceptable operating 
temperature and will then speed up to the originally 
set speed. 
To reset the motor, switch the power off then remove the 
power lead. After 30 seconds, plug the pump back into the 
mains power supply and resume normal operation. 

If the pump and filter are located below 
pool water level, it is necessary to fit 
isolating valves in the pipe between the 
pump and skimmer box and in return 
pipe from the filter to the pool.

The fittings on this product are 
constructed of ABS. Some PVC jointing 
compounds are incompatible with ABS. 
Check compound suitability before use.

CAUTION: In the interest of safety, we 
advise that all brands and types 
of pool pumps must be installed in 
accordance with AS3000 wiring rules 
or equivalent.

Henden recommends that all 
installations are fitted with earth 
leakage or residual current protection 
devices.

Warning! Ensure that an electrical 
isolation switch is located with easy 
access so that the pump can be 
switched off in an emergency.

Содержание H62SP













Отзывы: