background image

 

Quick Installation Guide 

 

 

Document 

WERA4-Quick-US-200917 

Page 34 of 73 

 

5.7 

Antenna Tuning 

5.6.1   Rx-Antenna Tuning 

The antenna tuning coils should be installed with contact grease and secured by means of 
the hose clamps. Please attach just loose for the first step, since the depth of shifting in 
the tuning coil into the pole will be used for fine tuning later on. Ensure that the ends of 
antenna poles (tubes) are clean inside and free of an oxide layer. If required clean with a 
metal brush.  

The radials should be connected with a little bit of contact grease as well. Attach the 
radials without mechanical stress to the guide ropes (using a cable clamp or tape) and 
wind it around the guide rope (5 to 10 turns). Attach the end of the radial to the peg by 
means of a guide rope. Use at least 50 cm guide rope to keep the end of the radial 
isolated from the ground. 

Now check the antenna tuning (resonant frequency) and matching (VSWR). We 
recommend using a battery driven antenna meter. 

 

 

Attaching radial to guide rope 

Radials twisted around guide rope 

 

 

Antenna meter with broad resonance  

Sharp resonance peak 

Содержание WERA










































































Отзывы: