Helmer i.series Скачать руководство пользователя страница 12

Страница: 12 / 45

Helmer Scientific i.Series

Ultra-Low Freezer

Service and Maintenance Manual

360173-A/C

3 Controls

i.Series

Ultra-Low freezers are equipped with the i.C³ monitoring and control system. The i.C³ system combines temperature

monitoring and control into a single user interface.

3.1

Home Screen and Screensaver

The Home Screen is the default screen and is displayed when:

♦

The Home icon is touched from any other screen.

♦

There is no interaction for two minutes on most screens other than those used to enter a password.

Home

Screen

Temperature

Graph

Screensaver

3.2

Home Screen Functions

Note

Refer to the i.C

User Guide for options available on all i.C

screens.

♦

View current interior cabinet temperature readings

♦ View min/max temperature occurrence for a specified time period

♦

View the current system time and date

♦ Access any of the five homescreen applications (touch

i.C

APPS

for additional applications)

♦

View information about current alarm events

♦

View whether the monitoring system is running on battery power

♦

Mute audible alarms

♦

View a graph of the chamber temperature

♦

View unit ID

Содержание i.series













































Результаты поиска

Содержание i.series

Отзывы:

Похожие инструкции для i.series

Бренды по названию

Популярные бренды

Helmer i.series, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание i.series

Отзывы:

Похожие инструкции для i.series

Бренды по названию

Популярные бренды