background image

MC6500GOPRO Camera Gimbal

 Page 5

DCS3600Digi

Digital Servo

Special for ROLL Axis.

1

3

2

STEP 5

|  Install the stabilizer bar

Please connect the servo to receiver's AIL Channel (for
Futaba is CH1) before link the camera mount to the servo
axis, confirm the neutrality point of the servo, then in-
stall while remaining the vertical angle towards the roll
arm.

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

12345678901

Connect to the 2nd. hole

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

12345678901234567890123456789012123456789012345678901234567890

Stabilizer bar can make the roll arm more stable in operation

23mm

Содержание MC6500GOPRO






Отзывы: