HEIL PT 1000 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 202

HEIL PT 1000 Скачать руководство пользователя страница 74

Issued September 2017
Controls, Switches, and Indicator Lights

Copyright 2017, Heil Environmental

Printed in U.S.A.

66

STANDARD OUTSIDE CONTROLS

The standard outside controls for the unit are located on
the front street side of the body and on the curb side of the
tailgate near the hopper.

The slide and packer blade levers have detents. Once you
push or pull the lever past the detent (fully push or pull the
lever), the selected operation continues and you can
release the lever. The lever will self-center at the end of the
commanded operation by way of internal hydraulic
pressure. You can reverse the direction of a function at any
time when you push or pull the lever past the detent in the
opposite direction.

You must move the tailgate and ejector levers in the
direction of travel you want and hold the lever at that
position until the tailgate or ejector reaches the desired
position then release the lever. You can stop an operation
at any time by releasing the lever.

DANGER

Your body or clothing can become caught by the blade
while it moves. Serious injury or death may occur if a
person is in or near the hopper when the blade and slide
assembly move. Clear the area near the hopper of all
unnecessary people before you move the blade and slide
assembly and keep all parts of your body away from the
blade.

A. PACKER BLADE Lever

This lever is on the curb side of the tailgate next to the
SLIDE lever. It is the lever closest to the end of the
tailgate. See the figures on the next two pages.

1. PUSH the lever to the FULL DOWN position and

RELEASE it to MOVE the blade UP.

2. PULL the lever to the FULL UP position and

RELEASE it to MOVE the blade DOWN.

3. MOVE the lever in the opposite direction to stop an

UP or DOWN operation at any time.

4. You usually operate this lever at the same time you

operate the SLIDE lever to:

a. OPEN the hopper to load refuse

b. CLOSE the hopper for the in-transit position

c. MOVE and COMPACT the refuse in the hopper to

the body.

B. SLIDE Lever

This lever is on the curb side of the tailgate next to the
BLADE lever. See the figures on the next two pages.

1. PULL the lever to the UP position and RELEASE it to

MOVE the slide assembly IN.

2. PUSH the lever to the DOWN position and

RELEASE it to MOVE the slide assembly OUT.

3. MOVE the lever in the opposite direction to stop an

IN or OUT operation at any time.

4. You usually operate this lever at the same time you

operate the BLADE lever to:

a. OPEN the hopper to load refuse

b. CLOSE the hopper for the in-transit position

c. MOVE and COMPACT the refuse in the hopper to

the body.

«
...
72
73
74
75
76
...
»

Содержание PT 1000











































































































































































































Отзывы:

Нет отзывов