HEIL PT 1000 Скачать руководство пользователя | Manualshive

Страница: 26 / 202

background image

Issued September 2017
Introduction

Copyright 2017, Heil Environmental

Printed in U.S.A.

18

PRODUCT NOMENCLATURE (CONTINUED)

Cart Tipper

– One or more optional cart tippers can be located on the tailgate assembly. An operator uses a cart tipper to

raise and dump a residential refuse container. The controls will be located on the rear, curb side of the unit.

DANGER

Do not use an arm mechanism or roll bar as a riding step. Obey safety messages and use the riding step for when
traveling on the unit. Serious injury or death may occur.

Comb Lift

and

Arm Mechanism

options allow operators to lift compatible waste containers and empty them into the

hopper. When using either of these optional devices the movement is controlled at the rear of the tailgate using a
sustained pressure control. Operators must ensure that nearby personnel are clear of the area around the movement of
the lifting mechanism. The area directly behind the containers must also be clear in the event of the loss of the container
during the lifting operation. Only containers that are in good condition should be used with a lifting device to prevent them
from dislodging from the lifting device. The tailgate mechanics should not be operated while the container and the
mechanism are in the raised position to prevent potential impact of the packing mechanism to the container.

CAUTION

Stand clear when the ejector panel is in motion. Keep side access door closed when ejector panel is in motion. Failure to
obey may result in minor or moderate injury.

NOTICE

Do not use the ejector panel to pack refuse against a closed tailgate (backpack). Packing refuse against a closed tailgate
may result in damage to body or ejector cylinder.

Ejector Panel & Cylinders

– The ejector panel and cylinders push the refuse out of the body when the tailgate is OPEN.

Ejector & Tailgate Controls

– These controls are located in the cab of the unit and allow an operator to OPEN the

tailgate and fully EXTEND the ejector panel, which pushes the refuse out of the unit. The operator then uses the controls
to RETRACT the ejector panel and CLOSE the tailgate.

«
...
24
25
26
27
28
...
»

Содержание PT 1000











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PT 1000

Бренд: Kellfri Страницы: 20

Бренд: ABI Attachments Страницы: 28

Бренд: Baja motorsports Страницы: 73

Бренд: Humbaur Страницы: 100

Бренд: Humbaur Страницы: 106

Бренд: Trail Rover Страницы: 34

Бренд: E-TON Страницы: 38

Бренд: Landoll Страницы: 80

Бренд: Landoll Страницы: 70

Бренд: Baja Страницы: 57

Бренд: Yamaha Страницы: 41

Бренд: Ski-Doo Страницы: 22

Бренд: Ski-Doo Страницы: 75

Бренд: Ski-Doo Страницы: 123

Бренд: Espina Страницы: 23

Tomberlin ESCAPE 2018

Бренд: Columbia Vehicle Group Страницы: 36

Hauler 4x4 Crew Diesel 2019

Бренд: Cushman Страницы: 72

HAULER 1200X EFI 2019

Бренд: Cushman Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды