HEIL PT 1000 Скачать руководство пользователя страница 101

Страница: 101 / 202

Issued September 2017
Daily Checklist

Printed in U.S.A.

CHECKS AND INSPECTIONS

INSPECTION

RESULTS CODE

The blade should move UP

The slide should move OUT

Operate each installed optional outside control located at the tailgate:

Reeving Mechanism

Release the cable hook from it storage eye and hold the hook

PUSH the control lever – the cylinder should OUT (EXTEND)

PULL the control lever – the cylinder should move IN (RETRACT)

Attach the cable hook to its storage eye

Winch

Release the cable hook from it storage eye and hold the hook

PUSH the control lever – the winch spool should UNWIND the cable from the
spool

PULL the control lever – the winch spool should WIND the cable on the spool

Attach the cable hook to its storage eye

Arm Mechanism

PULL the control lever – the lift arms should RAISE

PUSH the control lever – the lift arm should LOWER

Содержание PT 1000



























































































































































































Результаты поиска

Содержание PT 1000

Отзывы:

HEIL PT 1000, Руководство по эксплуатации, Страница: 101 / 202

Результаты поиска

Содержание PT 1000

Отзывы: