Heatrae Sadia PremierPlus Скачать руководство пользователя страница 3

3

1. Introduction

1.1 General

The following instructions are offered as a guide to the 
user and installer.

The installation must be carried out by a competent 
plumbing and electrical installer in accordance with 
Building Regulation G3 (England and Wales), Technical 
Standard P3 (Scotland) or Building Regulation P5 
(Northern Ireland) and the Water Fitting Regulations 
(England and Wales) or Water Byelaws (Scotland). 

1.2 Symbols used

In these instructions, various risk levels are employed 
to draw the user’s attention to particular information. In 
doing so we wish to safeguard the user, avoid hazards 
and guarantee the correct operation of the appliance.

DANGER

Risk of a dangerous situation causing serious 
physical injury.

WARNING

Risk of dangerous situation causing slight 
physical injury.

CAUTION

Risk of material damage.

 

Signals important information.

1.3 Abbreviations

 

`

T&P - Temperature & Pressure relief valve

 

`

PRV - Pressure Reducing Valve

 

`

Prv - Pressure relief valve

1.4 Liabilities

Manufacturers liability
Our products are manufactured in compliance with 
the requirements of the various applicable European 
Directives. 

This appliance complies with the requirements of the 
CE marking directive.

In the interest of UK customers, we are continuously 
endeavouring to make improvements in product 
quality. All the specifications stated in this document 
are therefore subject to change without notice.

Our liability as the manufacturer may not be invoked in 
the following cases:

 

`

Failure to abide by the instructions on using the 
appliance.

 

`

Faulty or insufficient maintenance of the appliance.

 

`

Failure to abide by the instructions on installing the 
product.

Installer's liability
The installer is responsible for the installation and the 
commissioning of the appliance. The installer must 
respect the following instructions:

 

`

Read and follow the instructions given in the 
manuals provided with the appliance.

 

`

Carry out installation in compliance with the 
prevailing legislation and standards.

 

`

Perform the initial start up and carry out any checks 
necessary.

 

`

Complete the commissioning checklist.

 

`

Explain the installation to the user.

 

`

If maintenance is necessary, warn the user of the 
obligation to check the appliance  and maintain it 
in good working order.

 

`

Give all the instruction manuals to the user.

Users liability
To guarantee optimum operation of the appliance, the 
user must respect the following instructions:

 

`

Read and follow the instructions given in the 
manuals provided with the appliance.

 

`

Call on qualified professionals to carry out 
installation and initial start up.

 

`

Get your installer to explain your installation to you.

 

`

Have your required checks and services done.

 

`

Keep the instruction manuals in good condition 
and close to the appliance.

This appliance can be used by children aged 
from 8 years and above and persons with 

reduced physical sensory or mental capabilities 
or lack of experience and knowledge if they 
have been given supervision or instruction 
concerning use of the appliance in a safe 
way and understand the hazards involved. 
Children shall not play with the appliance. 
Cleaning and user maintenance shall not be 
made by children without supervision.

Children must be supervised to ensure they 
do not play with the appliance.

Содержание PremierPlus





























Отзывы: