manualshive.com logo in svg

Heatrae Sadia Megaflo Eco SolaReady, Инструкция по эксплуатации

Поделиться
Скачать
Heatrae Sadia Megaflo Eco SolaReady Скачать руководство пользователя страница 4

PRODUCT SPECIFICA

TION

4

Introduction

Congratulations on your purchase of a Megaflo Eco SolaReady unvented water heater. The Megaflo Eco SolaReady is 
manufactured in the UK from top quality materials and meets all the latest relevant safety and constructional standards. 
The high grade Duplex stainless steel cylinder offers exceptional strength and corrosion resistance which is backed by a 
Lifetime guarantee* Its performance and insulation levels exceed the latest requirements of Building Regulation Part L.
The Megaflo Eco SolaReady unvented water heater can be fed directly from the cold water mains supply to the property 
without the need for separate feed cisterns or vent pipes. It is supplied complete with all its necessary inlet and safety 
controls, electric immersion heater(s) and, for indirect units, a cylinder thermostat, thermal cut-out, 2-port motorised valve 
and wiring centre.
Generally its pressure and flowrate performance will far exceed that from a comparable vented system, thermal store, 
multipoint instantaneous gas heater, or combination boiler.
Please read and understand this product guide before starting work. 
Please leave this product guide with the user following installation.
*See terms and conditions of user guide.

Component Checklist – see figure 1

Before commencing installation check that all the components for your Megaflo Eco SolaReady unit are contained in the 
package. The following components are supplied as standard with your Megaflo Eco SolaReady unit:

General Requirements

Important: Please read and understand this product guide before installing the Megaflo Eco SolaReady water heater. Incorrect 
installation may invalidate the guarantee. The Megaflo Eco SolaReady must be Installed, Commissioned and Maintained by 
a competent installer in accordance with Building Regulation G3 (England and Wales), Technical Standard P3 (Scotland) or 
Building Regulation P5 (Northern Ireland) and the Water Fitting Regulations (England and Wales) or Water Byelaws (Scotland). 
Following Installation and Commissioning, the operation of the heater should be explained to the user and the user guide left 
with them for future reference.
THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL, 
SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION 
OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED. 
CHILDREN SHALL NOT PLAY WITH THE APPLIANCE. CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY 
CHILDREN WITHOUT SUPERVISION
WARNING: Do not switch on if there is a possibility that the water in the heater is frozen.

Storage

The Megaflo Eco SolaReady is supplied on a pallet with its associated control kits. It should be stored upright in a clean, dy, 
frost-free environment prior to installation.

Siting the Megaflo Eco SolaReady

The Megaflo Eco SolaReady unit must be vertically floor mounted. It can be placed anywhere convenient provided the 
discharge pipe(s) from its safety valves can be correctly installed. Areas that are subject to freezing must be avoided. Ensure 
that the floor is of sufficient strength to support the “full” weight of the unit (refer to Tables 2 and 3 on page 7 for unit 
weights). Pipe runs should be kept as short as possible for maximum economy. Access to associated controls, immersion 
heaters and indirect controls should be possible for servicing and maintenance of the system. 
Please do not install valves or pipework (except discharge pipe) within 50mm (2”) of the T&P relief valve to allow your 
insulation set to be fitted. The insulation set is important to ensure heat and energy conservation. See page 12 for more 
information.
To aid installation, the Megaflo Eco SolaReady is provided with lifting points located in the base moulding and two lifting aids 
mounted on the upper rear casing. The weights of the units are noted on the tables on page 7, see tables 2 and 3.

Supplied attached
• Tundish
•   Factory fitted Indirect Thermostat and Thermal cut-out 

(Indirect units only)

•  Factory fitted immersion heater(s) and thermal controls
•  Cold Water Inlet Control Kit, comprising of:
  •  3 Bar Pressure Reducing Valve (Fig 3) Page 9
  •  8 Bar Pressure Relief Valve (Fig 4) Page 9
  •   Stop cock

 

•  Drain Valve

•   Factory fitted Temperature / Pressure Relief Valve (set at 

90ºC / 1 Mpa (10bar))

•  Thermostatic blending valve

Supplied loose
•  T&P Relief Valve Insulation Set
•  Wiring Centre (Indirect units only)
•  Sensor cable 13M
•  2-Port Motorised Valve (Indirect units only)
•  Solar circuit expansion vessel (including mounting bracket)
•    DHW expansion vessel (including mounting bracket)
•  Flexible solar expansion vessel connection pipe

Please note: For East / West array installations, the following 
kit is required:  7225731

Содержание Megaflo Eco SolaReady





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды