Heatilator HST-42D Скачать руководство пользователя

Страница: 36 / 49

3 in. (76 mm) tall legs

Ø 17 1/2 in. (444.5 mm) Round Hole to fit over cap

Length x Width to fit inside shroud

Figure 10.1 Radiation Shield

Shrouds

• Chase top shrouds may be field constructed where

permitted by regional building codes.

WARNING! Risk of Fire! Shrouds must be constructed

as specified. Improper construction may overheat chase

top.

NOTICE: Some regional codes require an agency-Listed

shroud. Consult your local building officials.

• Hearth & Home Technologies Inc. supplies UL listed

shrouds. See your dealer for details.

• The following field constructed shroud designs have

been tested for Hearth Technologies fireplace systems

and termination caps.

• The shrouds must be constructed from a minimum .018

in. (26 ga) thick aluminized steel.

• The wire mesh is optional but recommended and must

be .018 in. thick minimum, 1/2 in. mesh.

A. Radiation Shield

• Some shrouds require a radiation shield. Use where

specified.

• Radiation shield must be constructed of minimum 26 ga

sheet metal.

3 in (76 mm)

minimum

Min.

Base Dim.

Min.

Base Dim.

Min.

Top Dim.

Min.

Top Dim.

Min. Opening

Width

Min. Opening

Width

Figure 10.2 Open Top Shroud Dimensions

B. Field Constructed Shrouds

Heat & Glo • HST-42D • 27177 • Rev AF • 1/11

TS345

TR342

TR342/344TV

Min. Base Dims.

23 x 23

28 x 28

26 x 26

584 x 584

711 x 711

660 x 660

Radiation Shield

Required

Min. Top Dims.

20 x 20

25 x 25

23 x 23

508 x 508

635 x 635

584 x 584

Min. Opening Width

17 x 17

22 x 22

20 x 20

432 x 432

559 x 559

508 x 508

Open Top Shroud (TR342 caps require radiation shield)

Содержание HST-42D


















































Результаты поиска

Содержание HST-42D

Отзывы:

Похожие инструкции для HST-42D

Бренды по названию

Популярные бренды

Heatilator HST-42D, Руководство пользователя

Результаты поиска

Содержание HST-42D

Отзывы:

Похожие инструкции для HST-42D

Бренды по названию

Популярные бренды