Heatilator HST-42D Скачать руководство пользователя

Страница: 6 / 49

Listing and Code Approvals

NOTICE:

This fireplace is tested and approved as a

decorative fireplace. It should not be factored as a primary

heat source in residential heating calculations.

WARNING! Risk of Fire!

Hearth & Home Technologies

disclaims any responsibility for, and the warranty and

agency listing will be voided by the following actions.

DO NOT:

• install or operate damaged fireplace

• modify fireplace

• install other than as instructed by Hearth & Home

Technologies

• operate the fireplace without fully assembling all

components

• overfire

• install an unvented gas log set

• install any component not approved by Hearth &

Home Technologies

• install parts or components not Listed or approved
Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualified

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:

- Steel

- Iron

- Brick

- Tile

- Concrete

- Slate

- Glass

- Plasters

• Materials reported as passing

ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:

- Wood

- Compressed paper

- Plant fibers - Plastic

• Any material that can ignite and burn; flame proofed or

not, plastered or un-plastered

Heat & Glo • HST-42D • 27177 • Rev AF • 1/11

A. Appliance Certification

This fireplace may be installed in sleeping rooms EX-

CEPT in manufactured homes. If installed with a gas log

set, provisions for the National Fuel Gas Code must be

met.
This fireplace has been tested and listed for use with the

optional components specified in this manual. These op-

tional components may be purchased separately and in-

stalled at a later date. Installation of an outside air kit will

require significant reconstruction and is best if installed at

the time of fireplace installation.
Heat & Glo is a registered trademark of Hearth & Home

Technologies Inc.

This fireplace system has been tested and listed in accor-

dance with UL 127 and ULC-S610 standards by Under-

writers Laboratories Inc. for installation and operation in

the United States and Canada.

Содержание HST-42D


















































Результаты поиска

Содержание HST-42D

Отзывы:

Похожие инструкции для HST-42D

Бренды по названию

Популярные бренды

Heatilator HST-42D, Руководство пользователя

Результаты поиска

Содержание HST-42D

Отзывы:

Похожие инструкции для HST-42D

Бренды по названию

Популярные бренды