Heatilator HST-42D Скачать руководство пользователя

Страница: 15 / 49

Negative pressure results from the imbalance of air avail-

able for the fireplace to operate properly. It can be stron-

gest in lower levels of the house.
Causes include:
• Exhaust fans (kitchen, bath, etc.)

• Range hoods

• Combustion air requirements for furnaces, water heaters

and other combustion appliances

• Clothes dryers

• Location of return-air vents to furnace or air

conditioning

• Imbalances of the HVAC air handling system

• Upper level air leaks such as:

- Recessed lighting

- Attic hatch

- Duct leaks

To minimize the effects of negative air pressure:
• Install the outside air kit with the intake facing prevailing

winds during the heating season

• Ensure adequate outdoor air for

all

combustion

appliances and exhaust equipment

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the fireplace

• Avoid installing the fireplace near doors, walkways or

small isolated spaces

• Recessed lighting should be a “sealed can” design

• Attic hatches weather stripped or sealed

• Attic mounted duct work and air handler joints and seams

taped or sealed

• Basement installations should be avoided

WARNING! Risk of Asphyxiation! Negative pressure

can cause spillage of combustion fumes and soot. Fire

must draft properly for safe operation.

NOTICE: Hearth & Home Technologies Inc. recommends

the use of direct vent fireplaces in basements.

D. Negative Pressure

B. Design and Installation Considerations

Draft is the pressure difference needed to vent fireplaces

successfully. When a fireplace is drafting successfully, all

combustion byproducts are exiting the home through the

chimney.
Considerations for successful draft include:
• Preventing negative pressure

• Location of fireplace and chimney

Before

installing, determine the following:

• Where the fireplace is to be installed

• The vent system configuration to be used

• Gas supply piping

• Electrical wiring

• Framing and finishing details

• Whether optional accessories—devices such as a fan,

wall switch or remote control —are desired

NOTICE: Check building codes prior to installation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector, fire

officials or authorities having jurisdiction over restrictions,

installation inspection and permits.

NOTICE:

Hearth & Home Technologies assumes no

responsibility for the improper performance of the fireplace

system caused by:
• Inadequate draft due to environmental conditions

• Downdrafts

• Tight sealing construction of the structure

• Mechanical exhausting devices

• Improper location of the chimney

C. Draft

NOTICE: Junction box should be installed during initial

setup to avoid major reconstruction.

Heat & Glo • HST-42D • 27177 • Rev AF • 1/11

Содержание HST-42D


















































Результаты поиска

Содержание HST-42D

Отзывы:

Похожие инструкции для HST-42D

Бренды по названию

Популярные бренды

Heatilator HST-42D, Руководство пользователя

Результаты поиска

Содержание HST-42D

Отзывы:

Похожие инструкции для HST-42D

Бренды по названию

Популярные бренды