Heat Controller RAH-183G, Руководство пользователя

Страница: 15 / 20

Heat Controller, Inc. Room Air Heat Pump with R-410A Owner’s Manual
13
�
To ensure proper operation, aim the remote
control at the signal receiver on the air
conditioner.
�
The remote control signal has a range of
up to 20 feet.
Remote Control
Cool Mode
Use the
Cool
mode at
Low, Med, High
or
Auto Fan
Speed
for cooling. Use the
Temperature Increase
�
/Decrease
�
pads to set the desired temperature
between 61°F and 86°F in 1°F increments.
The compressor will cycle on and off to keep
the room at the set level of comfort.
Set the thermostat at a lower number and the indoor
air will become cooler. Set the thermostat at a higher
number and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on
while set to a Cool setting or if turned from a fan setting
to a Cool setting, it may take approximately 3 minutes
for the compressor to start and cooling to begin.
Fan Only Mode
Energy Saver Mode
Auto Fan Speed
In the case of a power outage or interruption, the
unit will automatically re-start in the settings last
used after the power is restored. If the
Power Outage Recovery Feature
Controls the fan.
ON—
The fan will cycle on and off with the
compressor. This results in wider variations of
room temperature and humidity. Normally used
when the room is unoccupied.
NOTE:
The fan may
continue to run for a short time after the compressor cycles off.
OFF—
The fan runs all the time, while the
compressor cycles on and off.
Set to Auto fan speed for the fan speed to auto-
matically set to the speed needed to provide opti-
mum comfort settings with the set temperature.
If the room needs more cooling, the fan speed
will automatically increase. If the room needs less
cooling, the fan speed will automatically decrease.
Use the
Fan Only
Mode at
Low, Med
or
High
fan
speed to provide air circulation and filtering
without cooling. Since fan only settings do not
provide cooling, a Set temperature cannot be
entered. The room temperature will appear
in the display.
TIMER OFF—
When the air conditioner is on,
it can be set to automatically turn off in 0.5 to
24 hours.
How to set:
Press the
TIMER 1–24hr
pad on the unit or
the pad on the remote control. Each
touch of the Increase
�
/ Decrease
�
pads on the
unit or the
Increase
+
/ Decrease
–
pads on
the remote control will set the timer in
0.5 hour or 1 hour intervals (the intervals is
0.5 hour as the delay timer below 10 hours;
To review the remaining time on the
TIMER
1–24hr
timer, press the
TIMER 1– 24hr
pad on the
unit or the pad on the remote control.
Use the
Increase
�
/ Decrease
�
pads on the unit
or the
Increase
+
/ Decrease
–
pads on the
remote control to set a new time if desired.
To cancel the timer,
press the
TIMER 1–24hr
pad
until the light on the
TIMER 1–24hr
pad goes off.
�
Make sure nothing is between the air conditioner
and the remote control that could block the
signal.
�
Make sure batteries are fresh and installed
correctly as indicated on the remote control.
Cooling Descriptions
For Normal Cooling—
Select the
Cool
mode and
High
or
Med
fan with a middle set temperature.
For Maximum Cooling—
Select the
Cool
mode
and
High
fan with a lower set temperature.
For Quieter & Nighttime Cooling—
Select the
Cool mode and Low fan with a middle set
temperature.
NOTE: Auto Fan Speed cannot be used when in the
Fan Only Mode.
feature was set, it will resume countdown. You may
need to set a new time if desired.
NOTE: Auto Fan Speed cannot be used when in the
Fan Only
Mode.
Heat Mode (On some models)
Use the
Heat
mode at
Low, Med, High
or
Auto Fan
Speed
for heating. Use the
Temperature Increase
/ Decrease pads to set the desired temperature
between 61°F and 86°F in 1°F increments.
13
the intervals is 1 hour as the delay timer above
10 hours ). The Set light will turn on while setting.
This time delay is required to protect the compressor.
fresh
TIMER -24hr
-24hr timer, press the TIMER -24hr pad on the
TIMER 0.5-24hr
TIMER 0.5-24hr
Timer/Delay OFF—
When the air conditioner is on,
Timer/Delay0.5-24hr
0.5
0.5 0.5
TIMER
0.5-24HR
DELAY
TIMER
0.5-24HR
DELAY