Heat Controller RAH-183G, Руководство пользователя

Страница: 8 / 20

Owner’s Manual Room Air Heat Pump with R-410A Heat Controller, Inc.
6
6
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
—
Save these
instructions for local inspector's use.
●
●
●
●
●
●
●
●
●
IMPORTANT
— Observe all
governing codes and ordinances.
Note to Installer
—
Be sure to leave thes e
instructions with the Consumer.
Note to Consumer
—
Keep these
instructions for future reference.
Skill level
—
I nstallation of this appliance
requires basic mechanical skills.
Completion time
—
Approximately 1 hour
We recommend that two people install
this product.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under the Warranty.
Question? Consumer information line (86-756) 8617555(Customer Service Center)
Installation
Air Conditioner
Instructions
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall
outlet you plan to use is only a 2-prong outlet,
it is your responsibility to have it replaced with
a properly grounded 3-prong wall outlet.
Some models require 230/208-volt a.c.,
protected with a time delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for
best performance and to prevent
overloading house or apartment wiring
circuits, which could cause a possible
fire hazard from overheating wires.
ELECTRICAL REQUIREMENTS
CAUTION:
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
Do not change the plug on the power cord
of this air conditioner.
Aluminum house wiring may present special
problems — consult a qualified electrician.
TOOLS YOU WILL NEED
Phillips head screwdriver
Ruler or tape measure Pencil
Level Scissors or knife
Flat-blade screwdriver
Power cord includes a current interrupter
device. A test and reset button is provided on
the plug case. The device should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner
and contact a qualified service technician.
Adjustable wrench
517-787-2100
6
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
—
Save these
instructions for local inspector's use.
●
●
●
●
●
●
●
●
●
IMPORTANT
— Observe all
governing codes and ordinances.
Note to Installer
—
Be sure to leave thes e
instructions with the Consumer.
Note to Consumer
—
Keep these
instructions for future reference.
Skill level
—
I nstallation of this appliance
requires basic mechanical skills.
Completion time
—
Approximately 1 hour
We recommend that two people install
this product.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under the Warranty.
Question? Consumer information line (86-756) 8617555(Customer Service Center)
Installation
Air Conditioner
Instructions
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall
outlet you plan to use is only a 2-prong outlet,
it is your responsibility to have it replaced with
a properly grounded 3-prong wall outlet.
Some models require 230/208-volt a.c.,
protected with a time delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for
best performance and to prevent
overloading house or apartment wiring
circuits, which could cause a possible
fire hazard from overheating wires.
ELECTRICAL REQUIREMENTS
CAUTION:
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
Do not change the plug on the power cord
of this air conditioner.
Aluminum house wiring may present special
problems — consult a qualified electrician.
TOOLS YOU WILL NEED
Phillips head screwdriver
Ruler or tape measure Pencil
Level Scissors or knife
Flat-blade screwdriver
Power cord includes a current interrupter
device. A test and reset button is provided on
the plug case. The device should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner
and contact a qualified service technician.
Adjustable wrench
6
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
—
Save these
instructions for local inspector's use.
●
●
●
●
●
●
●
●
●
IMPORTANT
— Observe all
governing codes and ordinances.
Note to Installer
—
Be sure to leave thes e
instructions with the Consumer.
Note to Consumer
—
Keep these
instructions for future reference.
Skill level
—
I nstallation of this appliance
requires basic mechanical skills.
Completion time
—
Approximately 1 hour
We recommend that two people install
this product.
Proper installation is the responsibility
of the installer.
Product failure due to improper installation
is not covered under the Warranty.
Question? Consumer information line (86-756) 8617555(Customer Service Center)
Installation
Air Conditioner
Instructions
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall
outlet you plan to use is only a 2-prong outlet,
it is your responsibility to have it replaced with
a properly grounded 3-prong wall outlet.
Some models require 230/208-volt a.c.,
protected with a time delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for
best performance and to prevent
overloading house or apartment wiring
circuits, which could cause a possible
fire hazard from overheating wires.
ELECTRICAL REQUIREMENTS
CAUTION:
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
Do not change the plug on the power cord
of this air conditioner.
Aluminum house wiring may present special
problems — consult a qualified electrician.
TOOLS YOU WILL NEED
Phillips head screwdriver
Ruler or tape measure Pencil
Level Scissors or knife
Flat-blade screwdriver
Power cord includes a current interrupter
device. A test and reset button is provided on
the plug case. The device should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner
and contact a qualified service technician.
Adjustable wrench
Flat-head screwdiver