Heat & Glo LUX36 Скачать руководство пользователя страница 42

Страница: 42 / 56

Heat & Glo • LUX36, LUX42 Installation Manual

• 2287-980 Rev. L

• 2287-980 Rev. L • 4/16

Finishing

A. Finishing Templates

Two side

nishing templates and one top

nishing

template are supplied with the appliance. They are
fastened to the shipping pallet. The templates are used
with the LMOD-36 and LMOD-42 decorative fronts when

nishing materials such as marble, tile or stone exceeding

one inch thick.

Note:

If the desired front is an FS-36 or FS-42, do not

use the supplied templates. Refer to Section 10.E for
template and

nishing information.

INSIDE FIT Method: The

nishing template pieces are

required for installations that require more than one inch
thick

nishing materials to be installed over the face of the

factory-supplied 1/2 inch non-combustible board. Refer
to section 13.E for more information.

OVERLAP Method: The supplied templates are not
required for

nishing materials less than one inch thick.

The required decorative front will overlap

nish materials

less than one inch thick. Refer to section 13.E for more
information.

Template installation instruction

Refer to Section 10.E for decorative front clearance
information.

2. If applicable, bend the left and right side templates for

the appropriate decorative front type using Figure 10.1
as a reference.

3. Locate the four threaded inserts on the inside edge of

the

replace and secure the side templates with the

Phillips screws provided. See Figure 10.2.

4. Bend the top template as shown in Figure 10.3 and

secure with the two screws provided.

5. Remove all template components once

nishing

materials are secured.

Note:

A thin layer of mortar may be applied over the

visible non-combustible board between

nishing material

and the

replace opening.

TOP FINISHING

TEMPLATE

SIDE FINISHING
TEMPLATES

Figure 10.2 Top and Side Finishing Template Locations

Figure 10.1 Side Finishing Template Bend - LMOD Decorative Fronts

3/4 IN.

3-1/4 IN.

Figure 10.3 Top Finishing Template Bend - LMOD Decorative Fronts

Figure 10.4 Top/Side Finishing Templates Installed

Содержание LUX36

























































Результаты поиска

Содержание LUX36

Отзывы:

Похожие инструкции для LUX36

Бренды по названию

Популярные бренды

Heat & Glo LUX36, Руководство по установке

Результаты поиска

Содержание LUX36

Отзывы:

Похожие инструкции для LUX36

Бренды по названию

Популярные бренды