manualshive.com logo in svg

Hearth Technologies Heat-N-Glo SL-550TRS-AU, Инструкция по установке и эксплуатации

Поделиться
Скачать
Hearth Technologies Heat-N-Glo SL-550TRS-AU Скачать руководство пользователя страница 29

29

1. "STOP!"  Read the safety information on

previous page.

2. To access controls, open the bottom grille.

3. Turn the valve control knob to the "OFF" position.

To do this, you must turn the knob clockwise

     to the "Pilot" position, and then

press in and continue turning clockwise

    to the "OFF" position.

GAS CONTROL VALVE

NOTE:  Knob cannot be turned from "PILOT" to

"OFF" unless knob is pushed in slightly.  Do not
force.

4. WAIT FIVE (5)  MINUTES TO CLEAR OUT

ANY GAS. Then smell for gas, including near
the floor.  If you then smell gas, STOP!  Follow
"B" in the safety information on the previous
page. If  you don't smell gas, go to the next step.

5. The pilot should not require accessing for lighting

purposes. The pilot is located inside the
combustion chamber.

2.3

LIGHTING INSTRUCTIONS

THERMOCOUPLE

THERMOPILE

6. To put the control in the pilot position, turn the

control knob counter-clockwise  

      to

the "Pilot" position.

7. To light the pilot depress the control knob and then

depress the red piezo button until it makes a
clicking sound.  It may be necessary to repeat this
step.  If the pilot does not light after 10 seconds,
go back to step 3.  The control knob should be held
down for a MINUTE after pilot ignition.

 • If the control knob does not pop out when

released, STOP-shut off the gas supply to
the fireplace control valve, and IMMEDIATELY
call your service technician or gas supplier.

• If the pilot will not stay lit after two tries, turn

the control knob to the "OFF" position and
call your service technician or gas supplier.

8. After the pilot has been lit, the burner can be turned

on by turning the knob counter-clockwise

     to the "ON" position.  Flip the ON/OFF

switch to the "ON" position.

9. Close the bottom grille.

LIGHTING INSTRUCTIONS

TO TURN OFF GAS APPLIANCE

1. Open the bottom grille.

2. Turn ON/OFF switch to "OFF".

3. Turn the valve control knob clockwise  

to the "Pilot" position, then depress knob and
continue turning to "OFF" position.

4. Close the bottom grille.

   PILOT BURNER

Содержание Heat-N-Glo SL-550TRS-AU








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды