manualshive.com logo in svg

Hearth Technologies Heat-N-Glo SL-550TRS-AU, Инструкция по установке и эксплуатации

Поделиться
Скачать
Hearth Technologies Heat-N-Glo SL-550TRS-AU Скачать руководство пользователя страница 2

2

IMPORTANT: Read all instructions carefully before starting installation.
Failure to follow these installation instructions may result in a possible fire
hazard and will void the warranty. Save this Manual for future reference.

Copyright 2000
Heat-N-Glo, a division of Hearth Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
Printed in U.S.A.

MODEL SL-550TRS-AU
IS AUSTRALIAN GAS ASSOCIATION
APPROVED FOR NATURAL GAS OR
PROPANE AS A BALANCED FLUE
HEATER.

Refer to the appliance data plates for gas
consumptions and pressures.

Installation of this appliance should only be
carried out by an authorized person in ac-
cordance with the manufacturer's instruc-
tions.  All relevant codes and regulations
laid down by the gas piping authorities,
municipal building regulations, electrical
wiring regulations and the requirements of
the AGA Gas Installation Code must be ob-
served.

This appliance and its components are
tested and safe when installed in accor-
dance with this Installation Manual. Report
to your dealer any parts damaged in ship-
ment, specifically check glass condition.
The gas logs and flue system components
are in separate packages.  Read all instruc-
tions before starting installation and follow

these instructions carefully during installa-
tion to ensure maximum benefit and safety.
Failure to follow them will void your war-
ranty and may present a fire hazard.

The Heat-N-Glo, a division of Hearth Tech-
nologies Inc. warranty will be voided by, and
Heat-N-Glo, a division of Hearth Technolo-
gies Inc. disclaims any responsibility for the
following actions:

• Installation of any damaged heater  or

flue system component

• Modification of the heater or balanced

flue system installation  other  than  as
instructed  by  Heat-N-Glo, a division of
Hearth Technologies Inc.

• Improper positioning of the gas logs or

the glass door

• Installation and/or use of any compo-

nent part not manufactured or approved
by Heat-N-Glo, division of Hearth Tech-
nologies Inc., not  withstanding  any  in-
dependent  testing laboratory  or  other
party  approval  of  such  component
part or accessory.

INSTALLATION AND OPERATION INSTRUCTIONS

PLEASE READ THIS MANUAL BEFORE INSTALLING

AND USING THIS APPLIANCE.

Содержание Heat-N-Glo SL-550TRS-AU








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды