manualshive.com logo in svg

Hearth Technologies Heat-N-Glo SL-550TRS-AU, Инструкция по установке и эксплуатации

Поделиться
Скачать
Hearth Technologies Heat-N-Glo SL-550TRS-AU Скачать руководство пользователя страница 19

19

1. Attach the First Flue Component to the

Starting Collars

To attach the first flue component to the starting
collars of the fireplace:

• Apply a 3/8 inch (10mm) bead of stove cement

around the inner pipe heater starting collar.

• Make sure that the heater rope gasket sup-

plied with the heater seals between the first
flue component and the outer heater wrap.

• Lock the flue components into place by sliding

the concentric pipe sections with four (4) equally
spaced interior beads into the heater collar or
previously installed component end with four (4)
equally spaced indented sections.

• When the internal beads of each outer pipe line

up, rotate the pipe section clockwise about one-
quarter (1/4) turn. The flue pipe is now locked
together.

Figure 17    Attaching the First Flue
                    Component to the Starting Collars

     WARNING: A 3/8 INCH (10MM)
BEAD OF STOVE CEMENT MUST BE
PLACED AROUND THE INNER PIPE
HEATER STARTING COLLAR BEFORE
ATTACHING THE FIRST F L U E
COMPONENT. FAILURE TO SEAL THIS
JOINT MAY CAUSE THE HEATER TO
OPERATE IMPROPERLY. SEE FIGURE 17.

WARNING: ENSURE THAT THE
FIBERGLASS ROPE GASKET

SUPPLIED WITH THE HEATER SEALS
BETWEEN THE FIRST FLUE COMPO-
N E N T  A N D   T H E   O U T E R   H E AT E R
WRAP.

2.  Continue Adding Flue Components

To continue adding flue components in accordance
with the pre-planned flue system configuration:

• Ensure that each succeeding flue component is

securely fitted and locked into the preceding com-
ponent in the flue system.

90° elbows may be installed and rotated to any point
around the preceding component’s vertical axis. If
an elbow does not end up in a locked position with
the preceding component, attach with a minimum
of two (2) sheet metal screws.

3. Install Support Brackets

For Horizontal Runs - The flue system must be
supported every five (5) feet (1.5M) of horizontal
run by a horizontal pipe support.

To install support brackets for horizontal runs:

•    Place the pipe supports around the flue pipe.

•    Nail the pipe supports to the framing members.

!

!

STARTING
COLLAR

FIRST
FLUE
COMPONENT

STOVE
SEALANT
BEAD
3/8" (10mm)

1 INCH (25mm)

Содержание Heat-N-Glo SL-550TRS-AU








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды