24
Temperature Sensors
The Aqua Plus 16v utilizes 10K ohm thermistor type sensors. Three sensors (water temperature, air temperature
and solar or dual equipment spa temperature) are included. If the Aqua Plus 16v is being used to control a solar
heating system, the solar sensor is required. If dual equipment will be used, the dual equipment spa sensor (spa
temperature for “Pool and Spa-Dual”) is required. If both solar and dual equipment are desired, another tempera-
ture sensor must be purchased separately. The sensors are provided with a 15 ft. cable. If a longer cable is
required, contact the Hayward service dept. (908-355-7995) for information on suitable cable types and splices.
See Temperature Sensors on page 6 for directions on installing sensors.
AIR
SENSOR
SOLAR
SENSOR
DUAL EQUIPMENT
SPA SENSOR
POOL/SPA
SENSOR
optional
optional
Wired Remote Display/Keypad
The Aqua Plus 16v main unit can connect to a maximum of 3 remote wired display/keypads. Wired display/
keypads must be ordered separately.
Use four conductor cable (typically phone cable) to connect the wired remote display/keypad with the Aqua Plus
16v Control Center as shown below. The maximum wiring distance is 500ft. (160m). Note that the terminals on
both the Aqua Plus 16v main unit and the wired remote display/keypad are numbered: Connect 1 to 1, 2 to 2, etc.
Refer to diagram below.
If multiple remote display/keypads are installed:
Never connect more than 2 wires to any terminal block. Two
remotes can be wired back to the Aqua Plus 16v main unit or the second display/keypad (and third, if applicable)
can be “daisy chained” with one display/keypad wired to the next. The maximum wire run from the Aqua Plus 16v
main unit to the furthest remote display/keypad is 500 ft (160m).
19
Accessing the Configuration Menus
Configuring the Aqua Plus 16v requires that you navigate through the Configuration Menu and input various infor-
mation. For more detailed information about using the Aqua Plus 16v menu system, refer to the Operation Manual.
To access the Configuration Menus
Configuration
Menu-Unlocked
Configuration
Menu-Locked
Press repeatedly until “Configuration Menu” is displayed
Move to configuration menu items
Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock
NOTE: The configuration menu automatically “locks” after 2 minutes of no buttons being pressed to
prevent unauthorized people from changing the control logic inadvertently and possibly damaging
the pool equipment or causing a “call back” to fix the configuration.
Configuration Menus
Each item needs to be programmed and may contain additional sub-menu items. Refer to the following pages for
information on programming.
Cell Type
T-CELL-15
Rotates between available Cell types
Move to next menu item
Move to next menu item
Chlorinator
Enabled
Display
Salt
Chlor. Config.
+ to view/change
Toggle between Display Salt (default) and Minerals
Toggle between Chlorinator Enabled and Disabled (default)
Move to previous/next configuration menu
Move to next configuration menu
Push to access Chlorinator option
Cell Type
T-CELL-15
Chlorinator
Enabled
Display
Salt
Chlor. Config.
+ to view/change
Chlorinator
The Aqua Plus 16v is shipped with the chlorinator enabled. The cell and flow switch must be installed
and the Aqua Plus 16v will automatically chlorinate both the pool and spa according to the desired
output setting (see Settings Menu in the Operation manual). If disabled, all displays relating to the
chlorinator will be suppressed.
When the chlorinator is enabled, the Pro Logic will automatically detect and control any Aqua Rite(s)
that is installed in the system.
Display
Allows for the display of salt (default) or mineral values.
Cell Type Selection
The Cell Type Menu appears after “Display Salt/Minerals” in the Chlorinator Configuration Menu.
The options are T-CELL-15 (default), T-CELL-9, T-CELL-5 or T-CELL-3. Make the proper selection
based on the chlorinator cell that is used in your system. Refer to the information below.
"T-CELL-3" = T-CELL-3, GLX-CELL-3-W
"T-CELL-5" = GLX-CELL-5, GLX-CELL-5-W
"T-CELL-9" = T-CELL-9, GLX-CELL-9-W
"T-CELL-15" = T-CELL-15, GLX-CELL-15-W
Chemistry Config.
to enter
Press to access Chemistry Config. Wizard
Move to previous/next menu item
Chemistry Configuration Wizard
Requires use of the optional AQL-CHEM Sensing Kit.
Following the steps of the Chemistry Config.
Wizard will set up the AQL-CHEM to sense ORP and pH levels and, if the chlorination function is
used, can configure the Pro Logic to generate the correct amount of chlorine to properly sanitize the
pool. Refer to the AQL-CHEM manual for more detailed information.
Wired Remote
Display unit
500 ft max
Connect screw terminals
“1” to “1”, “2” to “2”, etc.
1
2
3
4