Haussmann RFLNS Скачать руководство пользователя страница 63

Страница: 63 / 64

P/N 0387183_V

6-7

Reach-In

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

REPAIRING ALUMINUM COIL

The aluminum coils used in Hussmann merchandisers
may be easily repaired in the field. Materials are
available from local refrigeration wholesalers.

Hussmann recommends the following solders and
technique:

Solders

Aladdin Welding Products Inc.

P.O. Box 7188

1300 Burton St.

Grand Rapids, MI 49507

Phone: 1-800-645-3413

Fax: 1-800-645-3414

X-Ergon

1570 E. Northgate

P.O. Box 2102

Irving, TX 75062

Phone: 1-800-527-9916

NOTE:
Hussmann Aluminum melts at

1125°F (607°C)

Aladdin 3-in-1 rod at

732°F (389°C)

X-Ergon Acid core at

455°F (235°C)

Technique:

1. Locate Leak.

2. REMOVE ALL PRESSURE.

3. Brush area UNDER HEAT.

4. Use PRESTOLITE TORCH ONLY.
Number 6 tip.

5. Maintain separate set of stainless steel

brushes and USE ONLY ON
ALUMINUM.

6. Tin surface around area.

7. Brush tinned surface UNDER HEAT,
thoroughly filling the open pores around leak.

8. Repair leak. Let aluminum melt solder,

NOT the torch.

9. Don’t repair for looks. Go for thickness.

10. Perform a leak check.

11. Wash with water.

12. Cover with a good flexible sealant.

Permit Number:

20-05195

Содержание RFLNS

































































Результаты поиска

Содержание RFLNS

Отзывы:

Похожие инструкции для RFLNS

Бренды по названию

Популярные бренды

Haussmann RFLNS, Руководство по установке и эксплуатации

Результаты поиска

Содержание RFLNS

Отзывы:

Похожие инструкции для RFLNS

Бренды по названию

Популярные бренды