background image

Reach-In

P/N 0387183_V 

1-5

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Check the following before the rear of the case is posi-
tioned at its final location according to the store plan:

1.  The external braces must be reinstalled  
 

with (6) nuts per brace, torqued to 24 foot  

 pounds.

FINAL LOCATION

Once the case reaches its final location, reassemble the 
wireway and door handles as follows:

1. Reinstall wireway pan in reverse order of removal.

2. The ground lug must be reinstalled using the 
screws provided.

3. Replace the conduit connectors and plastic gromets 
to the wireway pan.

4. Replace wireway cover, bumper and door handles.

LEVELING

Merchandisers must be installed level to ensure proper 
operation of the refrigeration system and to ensure 
proper drainage of defrost water. When leveling mer-
chandisers, use a carpenter’s level as shown. 

Metal leveling shims or wedges are provided with each 
merchandiser for use if needed.

Rear external frames must be  

reinstalled securely before setting  

or unloading shelves.

D

o

 

not

 

walk

 

on

 

top

 

of

 

the

 

merchandIser

.

d

o

 

not

 

place

 

heavy

 

objects

 

on

 

case

.

Do not walk on top of merchandiser.

Do not store items or  

flammable materials atop the unit.”

Permit Number:

20-05195

Содержание RFLNS

































































Отзывы: