Operation and Maintenance
34
Caution !
Caution !
4.4.1.5 -Main movement controls
• test the movement by raising the fly jib in the direction it is mounted
then lowering it (control rep. 9, Photo 1, page 27).
• stop the descent of the fly jib when it is in the horizontal position
• then test the turret orientation movement in both directions (control
rep. 11, Photo 1, page 27) and the fly jib's telescopic extension and
retraction (control rep. 8, Photo 1, page 27).
• test the movement of the suspension platform (control rep. 7, Photo 1,
page 27) then lower the arm completely again (so that the platform is
close to the ground).
4.4.2 - Operations starting from the platform
NOTE :
When you wish to move, it is important to raise the suspen-
sion platform in order to prevent the platform from touching
the ground during movement.
(Photo 2‚ page 28)
• Get on the platform, respecting the instructions on maximum load,
and, if necessary, redistribute the load across the whole platform.
MAXIMUM LOAD: HA41PX: 230 kg
(i.e. 2 people)
NOTE :
If the load on the platform exceeds the authorised maximum
load, no movement is possible from the platform control unit.
The overload indicator on the platform control panel and the
alarm will alert the operator. It is then necessary to lighten the
load. There is no load restriction within the range.
4.4.2.1 -Control Panel Test
High and low speeds are only
possible if the machine is folded.
When even slightly deployed, only
micro speed is possible.
• make sure before all manoeuvres that the green indicator (control
rep. 4, Photo 2, page 28) is lit, check that the machine is under power
and that the selector is in the "platform" position
• make sure that the emergency stop key (control rep. 10, Photo 2,
page 28) is unlocked
• make sure that the error indicator (control rep. 9, Photo 2, page 28) is
switched off
• check the correct operation of the warning signal (control rep. 13,
Photo 2, page 28).
Work can then start.
4.4.2.2 -Test of the movements
To carry out a movement, it is necessary to press on the "dead man" pedal
to activate the desired control.
The selector (control rep. 1, Photo 2, page 28) makes it possible to choose
the control assignment (control rep. 3, Photo 2, page 28) to raise the arm
or operate the fly jib's telescopic functions
The speed and the angle of inclination of the controls correspond to its di-
rection, speed of movement and acceleration. If the floor is not horizontal,
correct the position of the platform by activating the compensation selector
of the platform (control rep. 19, Photo 2, page 28).
Test the movements of the telescopic function, suspension platform and
platform rotation with the associated selector.
Test the rotational movement of the turret by activating the control handle
(control rep. 2, Photo 2, page 28) towards the left then towards the right.
Содержание HA 41 PX
