Form No. GRM_CN-0818
18
English
MAINTENANCE
Replacing Display Light Bulbs
WARNING
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display light is an incandescent bulb that illuminates the
warming area. These bulbs have a special coating to guard
against injury and food contamination in the event of breakage.
To replace a display light bulb:
1. Disconnect the power supply and wait until the unit has
cooled.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF standards
for food holding and display areas. For 220–230 volt
applications, use Hatco P/N 02.30.058.00.
General
Glo-Ray Infrared Strip Heaters are designed for maximum
durability and performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, turn off power at circuit
breaker, and allow unit to cool before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
(0512) 6732-5091.
Use only Genuine Hatco Replacement Parts when service
is required. Failure to use Genuine Hatco Replacement
Parts will void all warranties and may subject operators of
the equipment to hazardous electrical voltage, resulting
in electrical shock or burn. Genuine Hatco Replacement
Parts are specified to operate safely in the environments
in which they are used. Some aftermarket or generic
replacement parts do not have the characteristics that will
allow them to operate safely in Hatco equipment.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch the finish of the unit,
marring its appearance and making it susceptible to soil
accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner to
clean plastic surfaces. Paper towel and glass cleaner may
scratch the material. Wipe off plastic surfaces using a soft,
clean, water-dampened cloth.
Cleaning
To preserve the finish of the unit, it is recommended that all
surfaces be cleaned daily.
1. Turn off the unit and allow the unit to cool.
2. Wipe down all metal surfaces with a water-dampened,
non-abrasive cloth. Stubborn stains may be removed with
a good stainless steel or non-abrasive cleaner. Clean hard
to reach areas using a small brush and mild soap.
3. Wipe dry the entire unit using a non-abrasive, dry cloth.
4. If equipped, clean the plastic sneeze guards using soft
cleaning cloths, mild soap, and water.
NOTICE
: Do not
use paper towel or glass cleaner on plastic surfaces—
scratching may occur.
Содержание GLO-RAY GR-18
