Form No. GRM_CN-0818
14
English
Adjustable Angle Bracket Mounting
Mounting a strip heater with adjustable angle brackets
permanently attaches the unit to the underside of a shelf. Units
can be mounted to a flat shelf or a shelf with rolled/flanged
edges. Adjustable angle brackets provide the necessary gap
between the unit and a combustible shelf.
CAUTION
To ensure safe and proper operation, refer to the “Minimum
Clearance Requirements” listed in the INSTALLATION
section of this manual.
NOTE: When mounting the unit under a shelf, it is recommended
to use remote-mounted control switches.
Use the optional adjustable angle brackets to mount the unit
below the lowest part of the rolled or flanged edge of the shelf
(a minimum gap of 25 mm [1″] is required between the unit
and the underside of a rolled or flanged shelf to prevent heat
damage to the electrical system of the unit).
25 mm (1″)
Gap
Minimum
Shelf with 19 mm (3/4″)
flanged edge
Adjustable
Angle
Bracket
Flanged Edge Shelf Installation
NOTE: GRN Series units are supplied with matching Designer-
colored angle brackets that provide 38 mm (1-1/2″)
clearance between the unit and an overshelf.
Adjustable Angle Bracket Mounting on Aluminum Models
Use the following procedure to install adjustable brackets on
each end of aluminum housing models (GRA, GRAH, GRAL,
and GRAHL).
1. Position the unit on a flat surface with the heating element
facing down.
2. Remove the two hanger tab screws and hanger tabs.
These items will not be needed.
3. Remove the two upper end plate screws.
4. Align the adjustable angle bracket with the end plate
mounting holes on the unit. Secure the angle bracket with
the previously removed end plate screws.
Removed
Hanger Tabs
Adjustable
Angle Bracket
End Plate
Screws
Aluminum Model Adjustable Angle Bracket Installation
5. Fasten the angle brackets to the underside of the shelf
using appropriate fasteners (not supplied by Hatco).
NOTE: Two pairs of brackets will be needed for dual units.
Two adjustable
angle brackets
on each end
for dual units.
Dual Unit Mounting
Adjustable Angle Bracket Mounting on
Stainless Steel Models
Use the following procedure to install adjustable angle brackets
on each end of stainless steel housing models (GR and
GRH models).
1. Position the unit on a flat surface with the heating element
facing down.
2. Remove the two hanger tab screws and hanger tabs.
3. Align the adjustable angle bracket with the hanger tab
mounting holes on the unit.
4. Secure the angle bracket with the previously removed
hanger tab screws.
5. Fasten the angle brackets to the underside of the shelf
using appropriate fasteners (not supplied by Hatco).
Removed
Hanger Tabs
Stainless Steel
Adjustable
Angle Bracket
Hanger Tab
Screws
Stainless Steel Model Adjustable Angle Bracket Installation
INSTALLATION
Содержание GLO-RAY GR-18
