background image

Form No. F2GPM-0721

3

English

IMPORTANT SAFETY INFORMATION

WARNING

FIRE HAZARD: Do not use an extension cord. If power 

cord is too short, contact a qualified electrician to 

determine and install proper voltage and size electrical 

receptacle near unit.
Make sure all operators have been instructed on the safe 

and proper use of the unit.
This unit is not intended for use by children or persons 

with reduced physical, sensory, or mental capabilities. 

Ensure proper supervision of children and keep them 

away from the unit.
This unit has no “user-serviceable” parts. If service 

is required on this unit, contact an Authorized Hatco 

Service Agent or contact the Hatco Service Department at  

800-558-0607 or 414-671-6350.

CAUTION

BURN HAZARD: Some exterior surfaces on unit will get 

hot. Avoid unnecessary contact with unit.
Locate unit in an area that is convenient for use. The 

location should be level and strong enough to support the 

weight of the unit and contents.
Do not move or relocate unit for cleaning. Unit is bulky 

and heavy.
Do not place anything on top of unit; doing so may subject 

personnel to injury or could damage unit.
Do not store any materials or items inside unit when not 

in use.
Never use steel pads, wire brushes, or scrapers to clean 

unit.

NOTICE

Do not locate unit in an area subject to ambient 

temperatures above 100°F (38°C). Doing so will damage 

unit and void warranty.
Unit must be level for self-closing doors to function 

properly.
Do not lay unit on its side in any direction. Damage to unit 

could occur.
Damage to any countertop material caused by heat 

generated from Hatco equipment is not covered under 

the Hatco warranty. Contact manufacturer of countertop 

material for application information.
Use non-abrasive cleaners and cloths only. Abrasive 

cleaners and cloths could scratch finish of unit, marring its 

appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain 

sanitary operation.

WARNING

ELECTRIC SHOCK HAZARD:

  •  Plug unit into a properly grounded electrical receptacle 

of the correct voltage, size, and plug configuration. If 

plug and receptacle do not match, contact a qualified 

electrician to determine and install proper voltage and 

size electrical receptacle.

 • Turn OFF power switch, unplug power cord, and 

allow unit to cool before performing any cleaning, 

adjustments, or maintenance.

  •  DO NOT submerge or saturate with water. Unit is not 

waterproof. Do not operate if unit has been submerged 

or saturated with water.

  •  Unit is not weatherproof. Locate unit indoors where 

ambient air temperature is a minimum of 70°F (21°C).

  •  Do not steam clean or use excessive water on unit.
  •  This unit is not “jet-proof” construction. Do not use 

jet-clean spray to clean this unit.

  •  Do not clean unit when it is energized or hot.
  •  Do not pull unit by power cord.
  •  Discontinue use if power cord is frayed or worn.
  •  Do not attempt to repair or replace a damaged power 

cord. Cord must be replaced by an Authorized Hatco 

Service Agent or a person with similar qualifications.

  •  Do not clean unit with metal scouring pads. Metal pieces 

can break off pad and touch electrical components, 

creating risk of electric shock.

  •  This unit must be serviced by qualified personnel only. 

Service by unqualified personnel may lead to electric 

shock or burn.

  • Use only Genuine Hatco Replacement Parts when 

service is required. Failure to use Genuine Hatco 

Replacement Parts will void all warranties and may 

subject operators of the equipment to hazardous 

electrical voltage, resulting in electrical shock or burn. 

Genuine Hatco Replacement Parts are specified to 

operate safely in the environments in which they are 

used. Some aftermarket or generic replacement parts 

do not have the characteristics that will allow them to 

operate safely in Hatco equipment.

EXPLOSION HAZARD: Do not store or use gasoline or 

other flammable vapors or liquids in the vicinity of this or 

any other appliance.
Install unit in accordance with installation instructions in 

this manual.
This unit is not designed for long-term food holding.  The 

holding time is programmable for up to 45 minutes upon 

placement of each order in a locker.  Manage or dispose 

of food products held for longer than safe holding time in 

accordance with all local food code requirements.
Use extreme caution when moving and tipping unit during 

installation. Size and weight of unit create significant tip 

and pinch point hazards. Remain aware and keep clear of 

unit/pinch points while tipping to avoid serious injury.

Read the following important safety information before using this equipment to avoid  

serious injury or death and to avoid damage to equipment or property

.

SAVE THESE INSTRUCTIONS

Содержание F2GBP Series









































Отзывы: