Hartzell HC-E4 3 Series Скачать руководство пользователя страница 234

Страница: 234 / 308

Propeller Owner’s Manual

147

MAINTENANCE PRACTICES

61-00-47

Page 6-24

Rev. 16 May/20

(5) Permit the solvent to evaporate.
(6) Apply masking material to the erosion shield, anti-icing

or de-ice boot, and tip stripes, as needed.

WARNING:

FINISH COATINGS ARE FLAMMABLE

AND TOXIC TO THE SKIN, EYES AND

RESPIRATORY TRACT. SKIN AND EYE

PROTECTION ARE REQUIRED. AVOID

PROLONGED CONTACT. USE IN A WELL

VENTILATED AREA.

CAUTION:

APPLY FINISH COATING TO UNIFORMLY

COVER THE REPAIR/EROSION. AVOID

EXCESSIVE PAINT BUILDUP ALONG THE

TRAILING EDGE TO AVOID CHANGING

THE BLADE PROFILE AND/OR P-STATIC

CHARACTERISTICS.

(7) Apply a

sufficient

amount of

finish coating to achieve

2 to 4 mils thickness when dry.
(a) Re-coat before 30 minutes, or after 48 hours.
(b) If the paint is permitted to dry longer than four hours,

it must be lightly sanded before another coat is

applied.

(8) Remove masking material from the tip stripes and

re-apply masking material for the tip stripe refinishing if

required.

(9)

Apply sufficient tip stripe coating to achieve 2 to 4 mils

thickness when dry.
(a) Re-coat before 30 minutes, or after 48 hours.
(b) If the paint is permitted to dry longer than four hours,

it must be lightly sanded before another coat is

applied.

(10) Remove the masking material immediately from the

anti-icing or de-ice boot and tip stripes, if applicable.

(11) Optionally, perform dynamic balancing in accordance

with the procedures and limitations specified in the

Dynamic Balance section of this chapter.

Содержание HC-E4 3 Series




















































































































































































































































































































Результаты поиска

Содержание HC-E4 3 Series

Отзывы:

Похожие инструкции для HC-E4 3 Series

Бренды по названию

Популярные бренды

Hartzell HC-E4 3 Series, Руководство пользователя

Результаты поиска

Содержание HC-E4 3 Series

Отзывы:

Похожие инструкции для HC-E4 3 Series

Бренды по названию

Популярные бренды