Hartzell HC-E4 3 Series Скачать руководство пользователя страница 231

Страница: 231 / 308

Propeller Owner’s Manual

147

MAINTENANCE PRACTICES

61-00-47

Page 6-21

Rev. 16 May/20

6. Blade Paint Touch-Up

(Rev. 1)

CAUTION:

INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE PROPELLER

CRITICAL PARTS. REFER TO THE

INTRODUCTION CHAPTER OF THIS

MANUAL FOR INFORMATION ABOUT

PROPELLER CRITICAL PARTS. REFER TO

THE ILLUSTRATED PARTS LIST CHAPTER

OF THE APPLICABLE OVERHAUL MANUAL(S)

FOR THE IDENTIFICATION OF SPECIFIC

PROPELLER CRITICAL PARTS.

A. Important Information

(1) Blade paint touch-up on Hartzell propeller blades may

be permitted when performed in accordance with the

instructions in this section.
(a) Composite Blades Only:

1 If the area to be painted is less than

10 sq.inches (6451.6 sq. mm), blade paint

touch-up is permitted.

2 If the area to be painted is greater than

10 sq. inches (6451.6 sq. mm), blade paint

touch-up is not permitted.
a Areas greater than 10 sq. inches

(6451.6 sq. mm) require the entire blade to

be repainted by a certified propeller repair

station with the appropriate rating.

B. Paint

(1) The paints listed in Table 6-1 have been tested by

Hartzell Propeller Inc. and are recommended for blade

touch-up.
(a) Alternate paints may be used for blade touch-up, but

Hartzell Propeller Inc. accepts no responsibility for

wear or adhesion-related issues.

Содержание HC-E4 3 Series




















































































































































































































































































































Результаты поиска

Содержание HC-E4 3 Series

Отзывы:

Похожие инструкции для HC-E4 3 Series

Бренды по названию

Популярные бренды

Hartzell HC-E4 3 Series, Руководство пользователя

Результаты поиска

Содержание HC-E4 3 Series

Отзывы:

Похожие инструкции для HC-E4 3 Series

Бренды по названию

Популярные бренды