Hartzell HC-E4 3 Series Скачать руководство пользователя страница 155

Страница: 155 / 308

Propeller Owner’s Manual

147

INSTALLATION AND REMOVAL

61-00-47

Page 3-65

Rev. 17 Sep/20

WARNING 1: DURING ENGINE INSTALLATION OR

REMOVAL, USING THE PROPELLER TO

SUPPORT THE WEIGHT OF THE ENGINE

IS NOT AUTHORIZED. UNAPPROVED

INSTALLATION AND REMOVAL

TECHNIQUES MAY CAUSE DAMAGE TO

THE PROPELLER THAT MAY LEAD TO

FAILURE AND RESULT IN AN AIRCRAFT

ACCIDENT.

WARNING 2: DURING PROPELLER REMOVAL,

AIRFRAME MANUFACTURER’S MANUALS

AND PROCEDURES MUST BE FOLLOWED

BECAUSE THEY MAY CONTAIN ISSUES

VITAL TO AIRCRAFT SAFETY THAT ARE

NOT CONTAINED IN THIS MANUAL OR THE

HARTZELL PROPELLER INC. OVERHAUL

MANUAL 157 (61-10-57).

WARNING 3: MAKE SURE THE SLING IS RATED UP

TO 800 LBS (363 KG) TO SUPPORT THE

WEIGHT OF THE PROPELLER ASSEMBLY

DURING REMOVAL.

(4) Cut and remove the safety wire or safety cable on the

propeller mounting nuts.

(5) Support the propeller assembly with a sling.

(a) Supporting the propeller with a sling may be delayed

until all but two mounting nuts and washers have

been removed to permit rotating the propeller for

ease of bolt removal.

(b) If the propeller will be reinstalled and it has

been dynamically balanced, make an identifying

mark on the propeller hub and a matching mark on

the engine flange to make sure of proper orientation

during re-installation to prevent dynamic imbalance.

Содержание HC-E4 3 Series




















































































































































































































































































































Результаты поиска

Содержание HC-E4 3 Series

Отзывы:

Похожие инструкции для HC-E4 3 Series

Бренды по названию

Популярные бренды

Hartzell HC-E4 3 Series, Руководство пользователя

Результаты поиска

Содержание HC-E4 3 Series

Отзывы:

Похожие инструкции для HC-E4 3 Series

Бренды по названию

Популярные бренды