Hartzell HC-C2YR-4CF/FC8475-6 Скачать руководство пользователя страница 153

Страница: 153 / 306

Propeller Owner's Manual

115N

INSTALLATION AND REMOVAL

61-00-15

Page 3-59

Rev. 24 Dec/20

C. Installation of a One-Piece Spinner Dome with a Removable

Plastic Forward Bulkhead

(1) Put the plastic adapter on the cylinder with the radiused

side of the adapter against the raised surface on the

cylinder as shown in Figure 3-16.

(2) Put ten spinner shims on top of the plastic adapter.

NOTE: The spinner shims are used to adjust the

spinner dome preload. Shims can be added

or removed after pre-fitting the spinner dome

later in this procedure.

(3) Put the forward bulkhead over the cylinder on top of the

spinner shims.

CAUTION: THE

FORWARD BULKHEAD MUST

FIT SNUGLY ON THE CYLINDER. AN

IMPROPERLY SUPPORTED DOME COULD

CAUSE CYLINDER DAMAGE OR A CRACK

IN THE DOME OR BULKHEAD.

(4) Using both hands, grasp the forward bulkhead and apply

lateral force (side-to-side).

(a) If there is no lateral movement: Go to step (5) of

this procedure.

(b) If there is lateral movement: Apply UHMW tape

CM137 in accordance with the following steps.

1 Option 1: Apply UHMW tape CM137 around

the ID of the forward bulkhead that fits over the

cylinder.

a Install 2.5 inch (63 mm) strips of UHMW

tape CM137 in equally spaced locations

around the ID of the forward bulkhead as

shown in Figure 3-16.

b If necessary, install additional layers of

UHMW tape CM137 until the forward

bulkhead fits snugly on the cylinder.

2 Option 2: Apply UHMW tape CM137 around the

cylinder.

a Wrap one or more layers of UHMW tape

CM137 around the cylinder until the forward

bulkhead fits snugly on the cylinder.

Содержание HC-C2YR-4CF/FC8475-6



















































































































































































































































































































Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды

Hartzell HC-C2YR-4CF/FC8475-6, Руководство пользователя и журнал учета

Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды