Harsco Industrial MACH C1500GG Скачать руководство пользователя страница 38

Страница: 38 / 61

MACH® Gas-Fired Boiler

Page 38

4.2.3 Normal Shut Down Procedures

1. Turn the on/off switch to the off position.

2. Close all manual gas valves. (if shutdown for extended period.)

4.2.4 Emergency Shut-Off

4.3

YPICAL

OILER

TILITY

EQUIREMENTS

MACH®

Boiler

Model

Input

Rating

(BTU/Hr)

Total

Amperage

Natural Gas

(1030 Btu/cu. ft.*)

Gas Rate

(CFH)

Output

Capacity

(Btu/hr)

C1500GG

1,500,000

Less than

1456*

1,440,000

C2000GG

2,000,000

Less than

1942*

1,920,000

Note:

The heat exchanger is constructed and stamped for 100 psig maximum operating pressure and 200º F

maximum temperature.

If overheating occurs or the gas

supply fails to shut off, do not turn off or disconnect the
electrical supply to the pump. Instead, shut off the gas
supply at a location external to the boiler.

Emergency Gas Shutoff

Close Both Valves

Содержание MACH C1500GG






























































Результаты поиска

Содержание MACH C1500GG

Отзывы:

Harsco Industrial MACH C1500GG, Инструкция по установке и эксплуатации, Страница: 38 / 61

Результаты поиска

Содержание MACH C1500GG

Отзывы: