Harsco Industrial MACH C1500GG Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 61

Harsco Industrial MACH C1500GG Скачать руководство пользователя страница 16

MACH® Gas-Fired Boiler

Page 16

3.5.3 Flue Venting

This boiler is not certified for use with Type "B" vent nor with PVC/CPVC venting.

This boiler

3.5.3.1

VENT SIZING

The vent must be sized in accordance with the ASHRAE Systems and Equipment handbook, Chapter 30 or according
to the vent manufacturer’s recommendations. When using manufactured venting systems, consult your vent supplier
for correct sizing and structural support requirements.

Table of Vent Design Parameters

MACH® Boiler Model

Frictional

Resistance

Stack

Temperature

CO

2

Natural Gas

CO

2

LP Gas

C1500GG - C2000GG

0.22”

185°F

9.2%

10.5%

All boiler venting systems should be designed by a qualified venting professional

experienced in venting system design. The information contained herein should be used as a guide only
and is not intended to be used in lieu of qualified technical expertise.

3.5.3.2

CATEGORY II INSTALLATIONS

The MACH

®

C1500GG and C2000GG boilers are dual-certified for both Category II and Category IV operation.

Category II appliances operate with a non-positive vent static pressure and with a vent temperature that may cause
excessive condensate production in the vent. There are several requirements for reliable operation of the boilers
under Category II conditions:

1. A stainless steel vent adapter is required to mate the boiler exhaust connection and the vent pipe. See the table

below for the applicable part numbers.

2. A normally-

closed motorized damper is required on the boiler’s air intake. See the table below for the applicable

part numbers.

3. The draft, measured inside the vent at the rear of the boiler,

must not exceed -

0.05” w.c.

Excessive negative

draft will cause nuisance trips such as flame failures.

4.

The vent system must be properly drained of condensate before returning to the boiler. Please see Section
3.5.3.6 for information on installing condensate drains in the exhaust vent.

All boiler venting systems should be designed by a qualified venting

professional experienced in venting system design. The information contained herein should
be used as a guide only and is not intended to be used in lieu of qualified technical expertise.

«
...
14
15
16
17
18
...
»

Содержание MACH C1500GG






























































Отзывы:

Нет отзывов