22
XXV Pellet Stove
Fig. 28
1"
See Hint #7.
Manual Start uP
helpful hints
1. Fines are small pieces of broken pellets (sawdust). Fines do not
flow easily and often build up on the hopper funnel bottom angles.
You can push these fines into the feeder opening and then fill the
hopper with pellets. As the system works, they will be burned. Or
you can clean them out before filling the hopper. As the system
works, they will be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may purge too much
fuel into the burn pot causing excessive smoke on start-up.
3. The firebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
4. Adjust Feed Rate. If this is your first fire or you are trying different
pellets, set the feed adjuster to #4, Fig. 26. This is a conservative
number and will probably need to be increased. After you know a
feed rate setting that works well, use that setting. Remember, if your
feed rate is too high you may waste fuel.
5. This is usually a weekly maintenance procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes off the front of the
burn pot into the ash pan. Then, scrape the top surface of the burn
pot downward into the base of the burn pot. When the stove is
ignited these scrapings will be pushed out by the feeder and burned.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied
a few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on "H".
Set the Temperature Dial to #7. Allow the unit to burn for about 30
minutes and check ash on front of burn pot. Fig. 28. If the ash line
is larger than 1", turn the feed adjuster from #3 to #4. Allow another
30 minutes of burn time and check again. If , at #6 setting, a 1" or
less ash bed is not obtainable, it is not a problem. The 1" ash bed
is only a maximum burn rate and at most normal settings the ash
bed will be larger.
Fig. 27
Fig. 26
igniter Switch to "Manual" (up position)
Make sure the unit is plugged into a 120 VAC, 60 HZ
electrical source.
iMPOrtant:
To avoid unwanted smoke, Be sure there
is no fuel or other combustibles in the ash pan prior to
lighting.
Keep all doors closed during operation. Maintain all
seals and gaskets in good condition.
Use only the burn pot, as supplied in the firebox, to
support or contain the burning fuel. No other form of
grate or rack is permitted.
1. turn Feed adjuSter to the desired feed rate
.
No. 4 is good for most pellets.
4
2. turn the MOde SelectOr to “OFF” and then to
the desired mode.
This will reset the control and
start the combustion motor.
3. turn the teMPerature dial to the desired
setting.
4. clean the burn pot with the scraper, if necessary.
5
5. Fill the burn pot with pellets, only level with front
edge.
(Do Not Over Fill).
nOte: if an automatic ignition was attempted -
be sure to give the appliance at least 30 minutes
of cooling time before proceeding with these
instructions.
6. add starting gel on top of the pellets.
Stir the gel
into pellets for faster lighting.
See cautiOn belOw.
The use of a starting gel that
is commercially marketed for use with pellet stoves
is permitted
OnlY
when performing a cold start. Also
be sure to perform the above steps in sequence to
ensure combustion blower operation before applying
the starting gel. Follow the starter manufacturer's
instructions for proper application.
7. light the starting gel with a match, and close the
door.
Operation will begin when the fire reaches the
proper temperature.
3
8. Fill the hopper with pellets and remove ashes as
required.
1, 6
DO NOT USE CHEMICALS OR FLUIDS TO START
THE FIRE. FOR ExAMPLE: NEVER USE GASOLINE,
GASOLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS
TO START OR "FRESHEN UP" A FIRE IN THIS
HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY
FROM THE HEATER WHILE IT IS IN USE.
cautiOn
Manual "cold" Start
Содержание XXV Pellet Stove
