background image

15

P68 Pellet Stove

autoMatic  ignition/oPeration

The P68 is a fully automatic stove that features two 

operating modes; 

Stove temperature Mode

 and 

room 

temperature Mode.

 In Stove Temperature Mode, you 

select a burn rate and the stove will remain at the same 

burn rate regardless of the room temperature. 

In the Room Temperature Mode the stove constantly 

monitors the temperature in the room and adjusts the size 

of the fire and the heat output of the stove so that the 

room is kept at a constant temperature. Room mode, in 

the AUTO position, has the added advantage of turning 

the stove off if no heat is required and turning the stove 

on again when the room temperature drops below your 

desired room temperature.  

room temperature Mode

 

Most consumers use the stove in the Room Temperature 

Mode because it is the easiest and most efficient method 

of keeping the room at a given temperature.  In the Room 

Temperature Mode, the Room Sensing Probe constantly 

monitors  room  temperature. As  the  weather  changes 

outside and your home needs varying amounts of heat to 

be at a desired temperature, the stove will automatically 

increase size and heat output of the fire so that a constant 

even temperature is maintained. If the weather warms up 

and no heat is required the stove will gradually shut down. 

When the house cools down the stove will automatically 

bring the room temperature to the precise temperature 

you desire.

In the Room Temperature Mode you can select either 

auto or Manual modes

 for the

 igniter 

using the igniter 

toggle  switch.  When  the  toggle  switch  is  in  the Auto 

position the igniter located inside the burn pot is ready 

to automatically light the fire when required.  When the 

toggle switch set to the Manual position the stove can 

be lit manually with either a gel or a wax type fire starter. 

(see lighting instructions on page 18.) With the igniter 

toggle switch set in the Manual position the stove will 

automatically adjust heat output, but the stove will not 

automatically shut down if no heat is required. Instead it 

will go to its lowest setting and remain there. The Manual 

position on the igniter toggle switch lets you light the stove 

manually, should the igniter fail for any reason. Secondly 

if you are using the Harman battery back up system the 

Manual setting will prevent the stove from turning off and 

on during a power failure, which would drain the back 

up battery, and possibly cause damage to the back-up 

or the stove.

In the Room Temperature Mode, the distribution blower 

speed can be increased or decreased by adjusting the 

Room Temp/Off/Stove Temp dial between L and H.  As 

output of the stove increases, the speed of the blower 

will increase  automatically to insure that more heat is 

transferred out into the room. The distribution blower will 

shut off as the room reaches the set temperature, this 

will prevent overheating of the room.

room  temperature  Mode: 

This  setting,  see  above, 

will produce a room temperature of 70 degrees with the 

distribution blower at medium speed.

room temperature Mode

KeeP aPPliance doorS cloSed While in 

oPeration. Maintain all SealS in good 

condition.

Содержание P68













































Отзывы: