Harman® • P-Series Installation Manual_R3 • 2018 - ___ • 09/20
5
8390-044I
NOTE:
Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specifications and/or price without notice.
Harman
®
is a registered trademark of Hearth & Home
Technologies.
F. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing
ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750° C
and
UL763
shall be
considered non-combustible materials.
G. Combustible Materials Specification
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or un-
plastered shall be considered combustible materials.
H. Electrical Codes
120 VAC, 60 Hz, Start 4.2 Amps, Run 2.8 Amps
NOTE: Some generator or battery back-up systems may
not be compatible with the micro-processor electronics
on this appliance. Please consult the power supply
manufacturer for compatible systems.
WARNING! Risk of Fire!
Hearth & Home Technologies
disclaims any responsibility for, and the warranty and agency
listing will be voided by the below actions.
DO NOT:
• Install or operate damaged appliance
• Modify appliance
• Install other than as instructed by Hearth & Home
Technologies
• Operate the appliance without fully assembling all
components
• Overfire
• Install any component not approved by Hearth &
Home Technologies
• Install parts or components not Listed or approved.
• Disable safety switches
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
E. BTU & Efficiency Specifications
* Weighted average LHV efficiency using data collected
during EPA emissions test.
**Weighted average HHV efficiency using data collected
during EPA emissions test.
***A range of BTU outputs based on EPA Default Efficiency
and the burn rates from the low and high EPA tests.
****Based on the maximum feed rate per hour multiplied by
approximately 8,600 BTU’s which is the average BTU’s from
a pound of pellets.
This wood heater needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood heater in a manner inconsistent with operating
instructions in this manual.
P43-C Freestanding Pellet Stove:
EPA Certification Number:
165-18
EPA Certified Emissions:
.95 g/hr
*LHV Tested Efficiency:
83.5%
**HHV Tested Efficiency:
77.9%
***EPA BTU Output:
16,600 - 30,900
****BTU Input:
17,200 - 43,500
Vent Size:
3 Inch
Hopper Capacity:
50 lbs
Fuel
Wood Pellet
P61-C Freestanding Pellet Stove:
EPA Certification Number:
177-19
EPA Certified Emissions:
1.5 g/hr
*LHV Tested Efficiency:
85%
**HHV Tested Efficiency:
79%
***EPA BTU Output:
17,100 - 46,800
****BTU Input:
21,400 - 60,700
Vent Size:
3 Inch
Hopper Capacity:
72 lbs
Fuel
Wood Pellet
P68-C Freestanding Pellet Stove:
EPA Certification Number:
178-19
EPA Certified Emissions:
1.4 g/hr
*LHV Tested Efficiency:
85%
**HHV Tested Efficiency:
79.5%
***EPA BTU Output:
15,900 - 53,100
****BTU Input:
20,200 - 67,600
Vent Size:
3 Inch
Hopper Capacity:
76 lbs
Fuel
Wood Pellet
