background image

12

A combustion blower is used to extract the com-

bustion gases from the firebox. This causes a nega-
tive pressure in the firebox and a positive pressure
in the venting system as shown in fig. 19. The longer
the vent pipe and more elbows used in the system,
the  greater the  flow  resistance.  Because of  these
facts we recommend using as few elbows as pos-
sible and 15 feet or less of vent pipe. The maximum
horizontal run should  not exceed 48". If  more than
15  feet  of pipe  is  needed,  the diameter  should  be
increased from 3" to 4" because a larger pipe causes
less  flow  resistance. 

Be  sure  to  use  approved

pellet vent pipe wall and ceiling pass- through
fittings  to  go  through  combustible  walls  and
ceilings. 

Be sure to use a starting collar to attach

the venting system to the stove. 

The starting col-

lar must be sealed to the stove with high temp
silicone caulking.

  + = Positive static pressure
     =  Negative static pressure

Outside air flex pipe
goes here

Inlet Cover part#
1-10-08542

Flex pipe part#
2-00-08543

HRV

When installing in a house with a Heat Reclaim-

ing Ventilation System (HRV) be sure the system is
balanced and is not creating a negative pressure in
the house.

Outside  Air

Outside air is optional except in mobile homes

and  where  building  codes  require.    The  benefit  of
outside  air  is  mainly  noticed  in  small,  very  tight
houses.

To  install  outside  air  use  2  3/8"  I.D.  flex  pipe

part number 2-00-08543. There is a break-away hole
on  the  rear  panel  which  must  be  removed  before
connecting the flex pipe. The pipe should be run out-
side and terminate to the side or below the vent pipe
outlet  so  the  flue  outlet  is  more  than  12"  from  the
inlet cover. The maximum length run of this pipe is
15 feet. If a longer run is needed, the size must be
increased to 3". Inlet cover part number 1-10-08542
should  be  used  to  keep  birds,  rodents,  etc.  out  of
pipe.

Fig.19

Room Sensor
Connection Ports

Venting

Vent  Pipe

Pellet venting pipe ( also known as PL vent ) is

constructed  of  two  layers  with  air  space  between
the layers. This air space acts as an insulator and
reduces the outside surface temperature to allow a
clearance  to  combustibles  of  only  3  inches.  The
sections  of  pipe  lock  together  to  form  an  air  tight
seal in most cases; however, in some cases a per-
fect  seal  is not  achieved.  For  this reason  and  the
fact that the Advance operates with a positive vent
pressure, 

we  specify  that  the  joints  also  be

sealed with  clear silicone.

Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

Содержание Advance Pellet Stove
































Отзывы: