background image

31

 

Harman Gold Warranty

HARMAN GOLD WARRANTY
6 YEAR TRANSFERABLE LIMITED WARRANTY
(Residential)
1 YEAR LIMITED WARRANTY (Commercial)

Harman Stove Company warrants its products to be free from defects in material or workmanship, in normal use and

service, for a period of 6 years from the date of sales invoice and for mechanical and electrical failures, in normal use and
service, for a period of 3 years from the date of sales invoice.

If defective in material or workmanship, during the warranty period, Harman Stove Company will, at its option, repair

or replace the product as described below.

The  warranty  above  constitutes  the  entire  warranty  with  respect  to  Harman  Stove  Company  products.    HARMAN

STOVE COMPANY  MAKES  NO  OTHER  WARRANTY,  EXPRESSED  OR  IMPLIED,  INCLUDING  “ANY”  WAR-

RANTY  OF MERCHANTABILITY,  OR  WARRANTY  OF  FITNESS  FOR  A  PARTICULAR  PURPOSE.  No employee,
agent, dealer, or other person is authorized to give any warranty on behalf of Harman Stove Company.  This warranty does
not apply if the product has been altered in any way after leaving the factory.  Harman Stove Company and its agents assume

no liability for “resultant damages of any kind” arising from the use of its products.  In addition, the manufacturer and its

warranty administrator shall be held free and harmless from liability from damage to property related to the operation, proper
or improper, of the equipment.

THERE  ARE  NO  WARRANTIES  WHICH  EXTEND  BEYOND  THE  DESCRIPTION  ON  THE  FACE  HEREOF.

THESE  WARRANTIES  APPLY only if the device is installed and operated as recommended in the user’s manual.

THESE  WARRANTIES WILL  NOT  APPLY if abuse, accident, improper installation, negligence, or use beyond rated

capacity causes damage.

HOW  TO MAKE A CLAIM - Any claim under this warranty should be made to the dealer from whom this appliance

was purchased.  Then contact is made with manufacturer, giving the model and serial numbers, the date of purchase, your

dealer’s name and address, plus a simple explanation of the nature of the defect.  Extra costs such as mileage and overtime

are not covered.  Nuisance calls are not covered by these warranties.

THIS   WARRANTY   IS   LIMITED   TO   DEFECTIVE   PARTS - REPAIR   AND/OR   REPLACEMENT   AT

HARMAN   STOVE  COMPANY’S   OPTION   AND   EXCLUDES   ANY  INCIDENTAL   AND   CONSEQUENTIAL

DAMAGES   CONNECTED  THEREWITH.

WARRANTY EXCLUSIONS: Failure due, but not limited to, fire, lightning, acts of God, power failures and/or surges,

rust, corrosion and venting problems are not covered.  Damage and/or repairs including but not limited to; remote controls,
filters,  fuses,  knobs,  glass,  ceramic  brick  panels,  ceramic  fiber  afterburners,  door  packing,  tile,  ceramic  log  sets,  paint,
batteries or  battery back-up  and related duct  work are not  covered. Also  excluded from this  warranty are  consumable or
normal  wear  items  including  but  not  limited  to;  flame  guides,  grates,  coal  bars,  afterburner  hoods,  fire  brick,  gaskets.
Additional exclusions for corn stoves are burnpot housing weldment, burnpot grate weldment (pellet or corn), burnpot front
plate (pellet or corn), burnpot front plate lock, corn auger extension, ceramic insert, and ceramic insert plate. Additional or
unusual utility bills incurred due to any malfunction or defect in equipment and the labor cost of gaining access to or removal

of a unit that requires special tools or equipment are not covered.  Maintenance needed to keep the stove in “good operating

condition” is not  covered.  This includes,  but is not limited to,  cleaning, adjustment of customer  controls and customer

education.    Labor,  materials,  expenses  and/or  equipment  needed  to  comply  with  law  and/or  regulations  set  forth  by  any
governmental agencies are not covered.

This Warranty provides specific legal rights and the consumer may have other rights that vary from state to state.
In the  event of  change in ownership,  the remaining  portion of this  warranty may  be transferred to  the new  owner by

sending the new owner information and a transfer fee  of $25.00 US to the Harman Stove Company.

PLEASE  READ  THE  LITERATURE  BY  THE  MANUFACTURER  FOR  THE  VARIOUS  ACCESSORY  DEVICES.

THE MANUFACTURER  WARRANTS  THESE  ACCESSORY  DEVICES,  NOT  HARMAN  STOVE  COMPANY  OR
THEIR WARRANTY  ADMINISTRATOR.   FURTHERMORE,  THESE  ACCESSORY  DEVICES  MUST  BE  INSTALLED
AND  USED ACCORDING  TO  THE  RECOMMENDATIONS  OF  THE  MANUFACTURER.

REMEDIES - The remedies set forth herein are exclusive and the liability of seller with respect to any contract or sale

or  anything done  in  connection therewith,  whether  in Contract,  in  tort, under  any  warranty, or  otherwise,  shall not,  except
as herein expressly provided, exceed the price of the equipment or part of which such liability is based.

CLARIFY - The above represents the complete warranty, which is given in connection with stoves, manufactured by

Harman  Stove  Company.   No  other  commitments, verbal  or  otherwise,  shall  apply except  by  a  written addendum  to  this
warranty.

Evaluation notes were added to the output document. To get rid of these notes, please order your copy of ePrint IV now.

Содержание Advance Pellet Stove
































Отзывы: