14
INSTALLATION AND CONNECTIONS
Installation and Connections
After unpacking the unit, and placing it on a
solid surface capable of supporting its weight,
you will need to make the connections to your
audio and video equipment.
Audio Equipment Connections
We recommend that you use high-quality inter-
connect cables when making connections to
source equipment and recorders to preserve the
integrity of the signals.
When making connections to audio source
equipment or speakers it is always a good
practice to unplug the unit from the AC wall
outlet. This prevents any possibility of
accidentally sending audio or transient signals to
the speakers that may damage them.
1. Connect the front, center and surround speaker
outputs
BCD
to the respective speakers.
Cables that are run inside walls should have the
appropriate markings to indicate listing with any
appropriate testing agency standards. Questions
about running cables inside walls should be
referred to your installer or a licensed electrician
who is familiar with the applicable local building
codes in your area.
When connecting wires to the speakers, be
certain to observe proper polarity. Note that the
positive (+) terminal of each speaker connection
now carries a specific color code. However, most
speakers will still use a red terminal for the
positive (+) connection. Con nect the “negative”
or “black” wire to the same terminal on both the
receiver and the speaker.
We also recommend that the length of cable
used to connect speaker pairs be identical. For
example, use the same length piece of cable to
connect the front-left and front-right or
surround-left and surround-right speakers, even
if the speakers are a different distance from the
HS controller.
2. Connections to the subwoofer are made via a
line level audio connection from the
Subwoofer
Output
7
to the line-level SUB input (purple)
of the subwoofer. Connect at the same time the
Subwoofer Trigger Output
F
to the Trigger
Input of the subwoofer.
3. Connect the supplied FM antenna to the
FM
(75 ohm)
connection
5
. The FM antenna may
be an external roof antenna, an inside powered
or wire lead antenna or a connection from a
cable system. Note that if the antenna or
connection uses 300-ohm twin-lead cable, you
should use a 300-ohm-to-75-ohm adapter to
make the connection.
Video Equipment Connections
Video equipment is connected in the same
manner as audio components. Again, the use of
highquality interconnect cables is recommended
to preserve signal quality.
Connecting the TV and optional
components
NOTE:
To be able to listen to the sound of a live
TV show through the loudspeakers of your HS
system you need a connection between the audio
output of your TV and the HS controller: to
achieve this when using the supplied SCART
cable, you don’t need to connect any additional
wires – the SCART cable transports audio and
video signals in both directions. But when using
the HDMI, Component, S-Video or compo site
jacks you need to connect the audio output of
your TV set with the
TV AUDIO IN
K
on the
back of your HS controller. If your TV has a digital
audio output, it is recommended to use that one
over the analog audio output. Connect the digital
output of your TV to the
DIGITAL IN
89
on
the back of your HS Controller.
HDMI Connection
If your TV set is equipped with an HDMI input, we
suggest you use the HDMI connection to connect
your HS system and your TV. It will allow you to
watch your DVD's in the best possible picture
quality. Most LCD, Plasma and video projectors
have such an HDMI input nowadays. Connect the
HDMI Output
H
to the HDMI Input of your
video device.
The HDMI wire does not transport audio signals
from the TV to the HS, thus you need an
additional audio connection (see note above).
If your TV set does not have an HDMI Input,
please follow one of the steps below to connect it
to your HS system or other video components.
TV Connection (method 1)
– using SCART cable (included)
To view the video from DVD discs on your TV set,
connect the SCART TV Out jack
3
of the HS
system to the SCART In jack of your TV set.
The audio connection runs through the same cable
(see note above).
TV Connection (method 2) – using S-Video
cable (not included)
If your TV set has an S-Video input jack you can
connect your TV to the S-Video out jack
1
on the
back of the HS controller. S-Video wires don’t
transport audio signals, thus you need an
additional audio connection (see note above).
TV connection (method 3) – using
composite video (cable not included)
If your TV set has neither S-Video nor SCART
input jacks, connect the Video Out jack
0
of the
HS to the Video In jack of your TV set. The
composite wire also doesn’t transport audio
signals, thus you need to make additional
connections (see earlier note).
Component Video Connection (method 4)
If the video display has component video inputs,
connect the Component Video Outputs
2
on
the HS 1000 to the cor res ponding input jacks on
your televi sion. If you are using a pro gres sive
scan television or projector, you must also
change the Scan Type in the DVD player's Video
Set-Up Menu from ”Interlaced” to
”Progressive”.
MODEL: HS 1000
COMPONENTS IN
MODEL: HS 1000
TV SET
AUDIO OUT
S-VIDEO IN
DIGITAL OUT
TV SET
AUDIO OUT
MODEL: HS 1000
MODEL: HS 1000
HDMI IN
AUDIO OUT
DIGITAL OUT
0122CSK - HK HS 1000 OM ENG v1.qxp:34252_HS350_Eng 03/03/09 9:15 Side 14
