PROGRAMMING THE REMOTE
55
Programming the Remote
Renaming
While the names given to the buttons and inputs
on the AVR represent recognizable categories of
audio/ video products, system operation may be
easier if the displays shown in the remote’s LCD
screen are customized to reflect the specific char-
acteristics of a playback source’s brand name or
the new function given to a specific button when
one remote’s controls are programmed into the
AVR remote. The AVR remote allows you to
change the name of either a master device or
any button on the remote using the following
steps.
Renaming a Device
To rename a specific device/input source button,
follow these steps. For this example, we will
show you how to rename the Device/Input
Selector normally shown as “TV” to “HDTV
TUNER.”
1. Press and hold the
Program Button
&
for
about three seconds while the message shown
in Figure 15 appears in the remote’s
LCD
Information Display
2
. Release the but-
ton when the red light under the
Set Button
F
appears.
2. The remote’s
MAIN MENU
message (Figure
16), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄¤
Navigation Buttons
E
until
RENAME
appears on the bottom
line of the LCD screen, as shown in Figure 66.
Figure 66
3. At the next menu screen press the
⁄¤
Navigation Buttons
E
until
RENAME
DEVICE
appears on the bottom line of the
LCD screen, as shown in Figure 67. Press the
Set Button
F
to begin renaming a device.
Figure 67
4. The next display screen (Figure 68) is where
you select the device that will be renamed. In
our example, that is the TV button. Press the
⁄¤
Navigation Buttons
E
until the
name of the base device appears and then
press the
Set Button
F
.
Figure 68
5. At the next menu screen you will see the
device name on the bottom line of the display
with a blinking cursor box to the right of the
device name. Press the
‹
Navigation
Buttons
E
to return the blinking cursor to
the far left side of the display line. You may
then retitle the device name as shown in the
next step.
6. To enter the new name, press the
Numeric
Keys
H
. The letters above the numbered
buttons indicate which letter or symbol will
appear when the button is pressed during the
renaming process. The first press of the button
will enter the first letter shown, subsequent
presses of the same button will change the
display to the other letters above that num-
bered key. For example, since the first letter we
need to rename the input to HDTV Tuner is an
“H”, you would locate the “H” above the “4”
button, and press the button twice. The first
press shows a “G,” the second press changes
it to an “H.” Consult the table at the end of
this section to see which characters pressing a
particular button generates.
7. After you enter the first letter of the new
device name, there are three options for enter-
ing the next character:
a. To enter a letter that requires a different
numeric key to be pressed, simply press
that button. The cursor will automatically
move to the next position and the first let-
ter accessed by the new button will appear.
Following our example, the next letter
needed is a “D,” so you would press the
“3” button once.
b. To enter a letter that uses the same numer-
ic key, you must first press the
›
Navigation Buttons
E
to move the
blinking cursor block to the next position.
Then press the
Numeric Key
H
as
required to enter the desired letter.
c. To enter a blank space, press the
›
Navigation Buttons
E
twice. The first
press will move the cursor to the right, and
the second press will move the cursor one
more space to the right, leaving a blank
space between the last letter and the next
one.
8. Repeat Step 7 as needed to enter all the
needed letters, numbers, characters and
spaces.
9. When the text entry is complete, press the
Set Button
F
. The LCD display will blink
DEVICE RENAMED
three times and then
return to normal operation.
Once a device is renamed you will see the new
name on the top line of the remote’s LCD display
whenever the
Input/Device Selector
4
is
pressed, or when any other command/function
button on the remote is pressed after the main
Device Selector is pressed. Note that renaming a
device in the remote will not change the name of
the input used by the on-screen menu system of
the AVR.
Notes on Renaming Devices:
• To move the cursor to the right or left of the
display during the renaming process, press the
‹
/
›
Navigation Buttons
E
as required.
• The table below shows the letters, numbers
and characters that may be accessed by press-
ing the Numeric Keys:
Key
Characters
Key
Characters
1
[,],/,1
6
M,N,O,6
2
A,B,C,2
7
P,Q,R,S,7
3
D,E,F,3
8
T,U,V,8
4
G,H,I,4
9
W,X,Y,Z,9
5
J,K,L,5
0
-,.,#,0
• Renaming a device changes the name of the
device only, not any of the individual key func-
tions within that device memory. To change the
name of an individual device, follow the
instructions in the next section.
Renaming Individual Keys
Thanks to the programming flexibility of the AVR
remote, an individual button on the remote may
be assigned a feature or function that is different
from the name that appears as the factory
default when the button is pressed. However,
with the Rename Key function it is possible to
rename almost any button on the remote so that
when the button is pressed you will see a more
descriptive or appropriate name displayed.
To rename a specific button on the remote, fol-
low these steps. For this example, we will show
you how to rename the
Tone Control Button
.
, which is normally not used when DVD is
selected so that it reads ZOOM in the remote’s
display.
1. Press and hold the
Program Button
&
for
about three seconds while the message shown
in Figure 15 appears in the remote’s
LCD
Information Display
2
. Release the but-
ton when the red light under the
Set Button
F
appears.
2. The remote’s
MAIN MENU
message (Figure
16), will appear in the LCD display and the
Set Button
F
will remain illuminated in
red. Press the
⁄¤
Navigation Buttons
E
until
RENAME
appears on the bottom
line of the LCD screen, as shown in Figure 66.
3. At the next menu screen press the
⁄¤
Navigation Buttons
E
until
RENAME
KEY
appears on the bottom line of the LCD
screen, as shown in Figure 69. Press the
Set
Button
F
to continue.
Figure 69
4. The next display screen (Figure 70) is where
you select the device within which the key to
be renamed exists. Press the
⁄¤
Navigation Buttons
E
until the name of
the base device appears. In our example, since
we want to rename a button within the DVD
device memory,
DVD
should appear in the
R E N A M E
R E N A M E K E Y
R E N A M E D E V I C E
T V
R E N A M E
R E N A M E D E V I C E
M A I N M E N U
R E N A M E
