background image

Page 26

For technical questions, please call 1-888-866-5797.

ITEM 57080 

        

Sa

FET
y

Op
Era

TiO

n

Main

TE

nan

CE

SET

up

Warranties

Limited 90 Day Warranty (retail)

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, 

and warrants to the original purchaser that this product is free from defects in materials and workmanship for the 

period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, 

to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper 

installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries 

to persons or property, or for incidental, contingent, special or consequential damages arising from the use of 

our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so 

the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL 

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY 

AND FITNESS, EXCEPT FOR THE EMISSIONS CONTROL SYSTEM WARRANTY BELOW.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. 

Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our 

inspection verifies the defect, we will either repair or replace the product at our election or we may elect to 

refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return 

repaired products at our expense, but if we determine there is no defect, or that the defect resulted from 

causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary 

from state to state.  HFT also warrants that the emissions control system on your engine is 

designed, built, and equipped so that it conforms to the United States Environmental Protection 

Agency’s (EPA) emissions requirements in effect at the time of manufacture.

Emissions Control System Warranty

The California Air Resources Board, the United States Environmental Protection Agency, and 

Harbor Freight Tools (HFT) are pleased to explain the exhaust and evaporative emissions (“emissions”) control 

system warranty on your [Model Year] Small Off-Road Engine, in addition to the Retail Warranty above. In California, 

new equipment that uses small off-road engines must be designed, built, and equipped to meet the State’s stringent 

anti-smog standards.  HFT must warrant that the emissions control system on your small off-road engine will be free 

from defects in material and workmanship for the period listed below, provided there has been no abuse, neglect, 

or improper maintenance of your small off-road engine leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-injection 

system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid fuel and fuel 

vapors), fuel caps, valves, canisters, filters, clamps, and other associated components.  

Also included may be hoses, belts, connectors, and other emissions-related assemblies.

Where a warrantable condition exists, HFT will repair or replace, at our option, 

your engine if at no cost to you, including diagnosis, parts and labor.

ManuFaCTurEr’S WarranTy COVEraGE

The exhaust and evaporative emissions control system on your small off-road engine is warranted for two years.  

If any emission-related part on your small off-road engine is defective, the part will be repaired or replaced by HFT.

OWnEr’S WarranTy rESpOnSiBiLiTiES

As the small off-road engine owner, you are responsible for the performance of the required 

maintenance listed in your Owner’s Manual. HFT recommends that you retain all receipts covering 

maintenance on your small off-road engine, but HFT cannot deny warranty coverage solely for the 

lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small off-road engine owner, you should however be aware that HFT may deny you warranty 

coverage if your small off-road engine or a part has failed due to abuse (including failure to follow the fuel use 

instructions contained in this manual), neglect, or improper maintenance or unapproved modifications.

You are responsible for contacting HFT as soon as the problem exists in order to obtain warranty 

repair or replacement, by doing either of the following: (a) contact HFT product support at 1-888-866-5797 

or [email protected]; or (b) bring the to your nearest Harbor Freight Tools retail store.  

The nearest Harbor Freight Tools retail store can be found on the internet at http://www.harborfreight.com.  

The warranty repairs or replacement should be completed in a reasonable amount of time, not to 

exceed 30 days.  If you have a question regarding your warranty coverage, you should contact 

HFT product support at 1-888-866-5797 or [email protected].

Содержание 57080





























Отзывы: