Harbor Freight Tools 57080 Скачать руководство пользователя страница 11

Страница: 11 / 28

Page 11

For technical questions, please call 1-888-866-5797.

ITEM 57080

FET

Era

Main

nan

SET

Electric Start

1. Turn the Economy Switch

to the OFF position.

2. Turn the Combination Switch to the

START position.

3. Turn the Engine Switch to START

position to start the Engine. If Engine

does not start within 3 seconds,

release Starter Button. Wait at

least 10 seconds, then try again.

4. After the engine starts, allow to run for

20 seconds then turn the Combination

Switch to the RUN position.

note:

If engine does not start, check

engine oil level. Engine will not

start with low or no engine oil.

note:

If warm engine does not start,

turn Combination Switch to RUN

before trying to start it again.

note:

Moving the Combination

Switch too fast could stall the Engine.

iMpOrTanT:

Allow the Engine to run

at no load for five minutes after each

start-up so that the Engine can stabilize.

CarBOn MOnOXiDE SHuTOFF

DanGEr! TO prEVEnT SEriOuS inJury anD DEaTH FrOM CarBOn MOnOXiDE inHaLaTiOn:

The Carbon Monoxide sensor is an additional layer of protection only. Do not use the

Generator in any area or situation that will allow carbon monoxide to accumulate.

• FLASHING RED LIGHT:

Dangerous levels of carbon monoxide gas

have built up. Leave immediately until

area has aired out. Move Generator to

well-ventilated area before operation.

• FLASHING YELLOW LIGHT:

Carbon monoxide sensor malfunction.

Sensor needs service. Call 1-888-866-5797 as

soon as possible. Do not use the Generator

until the sensor is working properly.

Carbon Monoxide sensor must only be serviced by qualified technician to restore it to original

settings. Do not modify or tamper with the Carbon Monoxide sensor. not following these

instructions can result in death or serious injury due to Carbon Monoxide sensor malfunction.

OFF

STarT

OFF

STORAGE

run

STarT

CHOKE

STarT

OFF

ECOnOMy

SWiTCH

LOW IDLE MODE

OFF

ENGINE SW.

STarT

OFF

STORAGE

run

STarT

CHOKE

ENGINE SW.

STarT

OFF

LOW IDLE MODE

OFF

STarT

OFF

STORAGE

run

STarT

CHOKE

STarT

OFF

EnGinE

SWiTCH

Содержание 57080





























Результаты поиска

Содержание 57080

Отзывы:

Похожие инструкции для 57080

Бренды по названию

Популярные бренды

Harbor Freight Tools 57080, Руководство пользователя и инструкции по безопасности

Результаты поиска

Содержание 57080

Отзывы:

Похожие инструкции для 57080

Бренды по названию

Популярные бренды