HARBEN 4018 US Van Pack Скачать руководство пользователя страница 15

Страница: 15 / 48

Operation

4.1. Operating Conditions

Operators of water jetting equipment should be fully conversant with the 'Industry Best

Practices for The Use of High-Pressure Water Jetting Equipment’, hereafter referred to as

'The Code of Practice'.

A copy of The Code of Practice is available upon request.

Please ensure that you read this Operation & Maintenance Manual in conjunction with the

Health & Safety Manual before operation.

4.2. Daily Checks

Carry out all daily checks. Full maintenance checks are detailed in Section 5 - Routine

Maintenance.

They are:



pump oil level



gearbox oil level



water filter cleanliness



engine oil level



tank water level

4.3. Pre-start Checks & Procedures

WARNING!

In cold weather check that machine is not frozen before starting (see

Antifreeze section 4.11). Serious injury can occur from ice bullets.

(H&S Sections 3

and 7)

2. Only operate the machine in a well-ventilated area.

(H&S Sections 3, 8, 9, and 12)

3. Ensure the vehicle is parked on a level surface, and the hand brake is applied.

(H&S

Sections 3, 11, and 13)

4. To fill water tank, connect to water supply. The water will fill the tank via the inlet hose

reel when the tank is full it will flow out the overflow. (

NOTICE: To comply with water

authority bylaws never fill the tank by putting a hose directly inside

)

5. Feed off the hose reel approximately 10 feet of high-pressure hose. Do not fit the

nozzle or gun at this point!

(H&S Section 3, 6, and 16)

WARNING!

Inspect hose before using. Damaged hose can lead to serious injury

if put under pressure.

(H&S Section 3, 6, and 16)

7. In order to avoid an interruption to the jetting operation please ensure that the hand

held ‘radio control unit’ is fully charged, this is to ensure the radio signal is at full

strength and not compromised while the unit is being operated in ‘remote’ mode.

NOTICE: Do not drop the handheld “radio control unit” (RCU) down a manhole

as this could cause it permanent damage. Please use the lanyard provided.

Содержание 4018 US Van Pack

















































Результаты поиска

Содержание 4018 US Van Pack

Отзывы:

Похожие инструкции для 4018 US Van Pack

Бренды по названию

Популярные бренды

HARBEN 4018 US Van Pack, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 4018 US Van Pack

Отзывы:

Похожие инструкции для 4018 US Van Pack

Бренды по названию

Популярные бренды