manualshive.com logo in svg

Haojue HJ110-2, Руководство по обслуживанию

Поделиться
Скачать
Haojue HJ110-2 Скачать руководство пользователя страница 54

Apply clean engine oil on the outer surface of
the piston pin.
Install the piston with the "IN" mark aligned to
the valve.
Install the piston pin and click the new pin
circlip securely.

NOTE:
Do not leave the pin circlip opening aligned to
the piston gap.
Do not let the pin circlip fall into the crankcase.

●

●

●

●

●

●

●

●

CYLINDER REASSEMBLY

Install the dowel pin and new sealing gasket.

Apply engine oil on the outer surface of the
piston as well as on the ring slot and inner
cylinder wall.
Compress the cylinder installed with piston
rings.

NOTE:
Avoid damaging the piston rings during assembly.
Do not let the timing chain fall into the crankcase.

Apply engine oil on the inner surface of the
timing chain guide wheel.
Install the timing chain guide wheel, new
sealing washer and guide pin bolt.

E N G I N E

3 - 2 5

OIL

Engine oil

OIL

Engine oil

https://www.motomanuals.net/

Содержание HJ110-2











































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды