manualshive.com logo in svg

Haojue HJ110-2, Руководство по обслуживанию

Поделиться
Скачать
Haojue HJ110-2 Скачать руководство пользователя страница 154

Symptom and possible causes

Remedy

Complaint

1.Too much engine oil in the engine.
2.Worn piston rings or cylinder.
3.Worn valve guides.
4.Cylinder wall scored or scuffed.
5.Worn valves stems.
6.Defective stem seals.

Check and drain excess oil.
Replace.
Replace.
Replace.
Replace.
Replace.

Dirty or heavy
exhaust smoke.

7-3

SERVICING INFORMATION

Overflow and fuel
level fluctuations.

Replace.
Replace.
Check and adjust.
Clean.

1. Needle valve is worn or damaged.
2. Spring in needle valve is broken.
3. Float is not working properly.
4. Foreign matter has adhered to needle valve.

Idling or low-speed
trouble.

Medium or high-speed
trouble.

1. Main fuel jet or main air jet is clogged.
2. Main jet is clogged.
3. Throttle valve is not operating properly.
4. Filter is clogged.

1. Idle jet and idle air jet are clogged or loose.
2. Idle outlet or bypass is clogged.
3. Choke is not fully closed.

Check and clean.
Check and clean.
Check and adjust.

Check and clean.
Check and clean.
Adjust
Check and clean.

1. Clutch control out of limit or loss of play.
2. Weakened clutch springs.
3. Worn or distorted pressure plate.
4. Distorted clutch plates, driven and drive.

Adjust.
Replace.
Replace.
Replace.

Slipping clutch.

1.Clutch control out of limit or too much play.
2.Some clutch springs weakened.
3.Distorted pressure plate or clutch plates.

1.Broken gearshift cam.
2.Distorted gearshift forks.
3.Worn gearshift pawl.

1.Broken return spring on shift shaft.
2.Shift shafts are rubbing or sticky.
3.Distrorted or worn gearshift forks.

1.Worn shifting gears on driveshaft or countershaft.
2.Distorted or worn gearshift forks.
3.Weakened stopper pawl spring on gearshift cam.
4.Worn gearshift pawl.

Adjust.
Replace.
Replace.

Replace.
Replace.
Replace.

Replace.
Repair.
Replace.

Replace.
Replace.
Replace.
Replace.

Dragging clutch.

Transmission will
not shift.

Transmission will
not shift back.

Transmission jumps
out of gear.

1. Heavy carbon deposit on piston crown.
2. Not enough oil in the engine.
3. Defective oil pump or clogged oil circuit.
4. Air leak from intake pipe.
5. Use of incorrect engine oil.

Clean.
Add oil.
Repair or clean.
Retighten or replace.
Change.

Engine overheats.

https://www.motomanuals.net/

Содержание HJ110-2











































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды