Hanter® Wireless Intelligent Alarm Systems - Model HM2088
c. Back up Batteries
Open the cover at the back of the Control Panel. Placed the batteries into the
battery compartment and close the cover plate. Do not make any short connection
of the battery terminals under any circumstance. The battery can provide up to 36
hours of power to the Control Panel when there is main power failure.
4.1.2 Keychain Remote control
The Keychain Remote Control can be used to operate the Control Panel as the
following:
4.1.3 Indoor Wired Siren
When alarm system is in alarm mode, the siren will emit a loud sound of 110db. It
can be installed on any location with enclosed adhesive tape or screws and connect
it to the siren port of Control Panel.
Note: With the completing program the 4 set of numbers will maximize the duration of
Alarm Buzzing to approximately 5 minutes
.
4.1.4 Wireless Magnetic Door/Window Switch
It is a 2-piece unit. You can locate the switch unit and magnet bar onto two frames
of the door or window. When the door or window frames separates i.e. the switch
unit and the magnet bar are separated. The switch unit will transmit the signal to the
Control Panel to trigger the alarm siren and then process of auto-dialing to the
pre-set phone numbers will take place.
4.1.5 Wireless Motion Sensor (PIR)
The wireless Motion Sensor adopts wireless digital and microprocessor technology
with low energy consumption design. The core technology of the infrared detector,
the operational amplifier chip, employs custom designed mask (three sets of
built-in operational amplifier, capable of processing digital and analog signals
simultaneously), which makes it a highly intelligent detector with wireless
transmission of digital signals combined with low energy consumption.
4.1.6 Wireless Emergency Help Button
The Wireless Emergency Help Button is a wireless Remote Control Unit. In the
event of emergency, just press the Emergency Help Button.
P. 6
Hanter® Wireless Intelligent Alarm Systems - Model HM2088
6.2 Wireless Door/Window Magnet Switch
The Door/ Window Magnet Switch is equipped with a magnet bar.
(Movement of the magnet triggers an internal sensor in the switch). We
recommend locating the switch unit on the wall at the frame of the door or
window, with the magnet bar on the moving part of the door or window.
Step 1: Open the switch’s cover by screwdriver.
Step 2: Install the switch to the desired location, using the two screws or
adhesive tape.
Step 3: Ensure that the antenna is vertical (pointing up or down).
Step 4: Attach the magnet bar, using the screws or adhesive tape, to the
moving part of the door or window. The gap between the switch and
magnet bar should not be wider than 1.5cm when the door is closed.
Step 5: Opening and closing of the door/window will be confirmed by the
switch’s LED.
Reminder: If the switch or magnetic bar is fix directly on a metal surface, one is
advisable to pre-attach an insulator (plastic piece) in order not to affect the
signal transmission strength of the units.
6.3 Wireless Motion Sensor (PIR)
Step 1: Pry off the back plate with a small screwdriver, and install the
provided battery into the back of PIR detector.
Step 2: Mount the bracket with screws provided at any place you think has
the best coverage by the PIR sensor. Recommended height is about
2.1 meters above the floor.
Step 3: Mount the PIR sensor onto the bracket. The maximum distance
coverage area is up to 12 meters, and it has a detection angle of: 120
degree horizontally, 60 degree vertically.
Reminder:
1)
Do not place the detector close to any heating/cooling vents or near any
other object that often changes temperature.
2)
The PIR detector should not be placed near any item that generates a
strong electromagnetic signal. (transmitters, electronic regulators etc.)
3)
Avoid locations that have intense air circulation.
6.4
Wireless Smoke Detector
Step 1: Install the detector to the desired location
Step 2: Drill two holes on the wall or ceiling per the whole sizes of the
mounting bracket.
Step 3: Fix the mounting bracket on the wall or ceiling with the screws.
Step 4: Twist and lock the detector with the mounting bracket.
P. 15
Away Arm
Home Arm
Emergency help
Disarming