manualshive.com logo in svg

Hanna Instruments HI 83200, Инструкция по эксплуатации

Поделиться
Скачать
Hanna Instruments HI 83200 Скачать руководство пользователя страница 55

108

109

• Press ZERO key. The display will show “-0.0-” when the meter is zeroed and ready for measurement.

• Remove the cuvette and add the content of one packet of

HI 93750B-0 reagent. Replace the cap and gently mix for

one minute by slowly turning the cuvette upside down.

• Reinsert the cuvette into the instrument.

• Press TIMER and the display will show the countdown prior to the

measurement or, alternatively, wait for 2 minutes and press

READ. When the timer ends the meter will perform the reading.

The instrument displays the results in mg/L (ppm) of potas-

sium (K).

• Press the 

 

or

 

 

to access the second level of functions.

• Press the 

Chem Frm

 functional key to convert the result in mg/L of potassium oxide (K

2

O)

• Press the 

 

or

 

 

to go back to the measurement screen.

• For ULTRA HIGH RANGE samples: follow the procedure described at page 110.

Potassium HR

Potassium HR

POTASSIUM HIGH RANGE

SPECIFICATIONS

Range

20 to 200 mg/L

Resolution

5 mg/L

Accuracy

±30 mg/L ±7% of reading

Typical EMC

±5 mg/L

Deviation
Light Source

Tungsten lamp with narrow band interference filter @ 610 nm

Method

Adaptation of the Turbidimetric Tetraphenylborate method. The reaction between

Potassium and reagents causes turbidity in the sample.

REQUIRED REAGENTS

Code

Description

Quantity

HI 93750A-0

Potassium Reagent

6 drops

HI 93750B-0

Powder Reagent

1 packet

REAGENT SETS

HI 93750-01 

Reagents for 100 tests

HI 93750-03 

Reagents for 300 tests

For other accessories see page 128.

MEASUREMENT PROCEDURE

Note: for sample preparation follow the NUTRIENT SOLUTIONS (HR) procedure at page 19.

• Select the 

Potassium HR method using the procedure

described in the 

Method Selection section (see page 12).

• Fill the cuvette with 10 mL of sample, up to the mark.

• Add six drops of HI 93750A-0, replace the cap and swirl

the solution.

• Place the cuvette into the holder and close the lid.

10 mL

x 6

Содержание HI 83200




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды