manualshive.com logo in svg

Hanna Instruments HI 83200, Инструкция по эксплуатации

Поделиться
Скачать
Hanna Instruments HI 83200 Скачать руководство пользователя страница 28

54

55

Cyanuric Acid

CYANURIC ACID

SPECIFICATIONS

Range

0 to 80 mg/L

Resolution

1 mg/L

Accuracy

±1 mg/L ±15% of reading

Typical EMC

±1 mg/L

Deviation

Light Source

Tungsten lamp with narrow band interference filter @ 525 nm

Method

Adaptation of the turbidimetric method. The reaction between cyanuric acid and the

reagent causes a white suspension in the sample.

REQUIRED REAGENTS

Code

Description

Quantity

HI  93722-0

Powder  reagent

1 packet

REAGENT SETS

HI 93722-01

Reagents for 100 tests

HI 93722-03

Reagents for 300 tests

For other accessories see page 128.

MEASUREMENT PROCEDURE

• Select the 

Cyanuric Acid method using the procedure de-

scribed in the 

Method Selection section (see page 12).

• Fill the cuvette with 10 mL of unreacted sample (up to the

mark) and replace the cap.

• Place the cuvette into the holder and close the lid.

• Press ZERO key. The meter will show “-0.0-” when the

meter is zeroed and ready for measurement.

• Fill a graduated beaker up to the 25 mL mark with the

sample, add the content of one packet of HI 93722-0 reagent
and swirl gently to mix.

10 mL

Cyanide

INTERFERENCES

Interference may be caused by large amounts of turbidity that will cause high readings.
Oxidizing (such as chlorine) or reducing agents (such as sulfide or sulfur dioxide) are known to interfere with
the measurement. Distillation will remove these.
Samples with high pH values should be adjusted to approximately pH 7 before testing.

CAUTION:

 cyanides, their solutions, and hydrogen cyanide liberated by acids, are very poisonous.

• Press the 

 

or

 

 

to access the second level of functions.

• Press the 

Chem Frm

 functional key to convert the result in mg/L of Potassium Cyanide (KCN).

• Press the 

 

or

 

 

to go back to the measurement screen.

Note

:

 for most accurate results perform the test at 20-25 °C.

Содержание HI 83200




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды