HANGCHA CPD10-A Скачать руководство пользователя

Страница: 9 / 82

Main display interface

Battery capacity display[A]

Indicates the available residual capacity.

As the following diagram shows, from the left

to the right, the battery decreases from full

state to the only one case, which represents

that the battery leaves only 20%. Thus the

whole battery indicator bar will twinkle, and the

state indicator lamp will be bright, now please

stop working and charge immediately.

CAUTION



Charging in time is very important,

otherwise it will affect the lift-span

of battery

！

Service hours display[B]

Hourglass icon indicates that timing function.

When you turn off the key switch, the hour

meter will works and the minimum unit is 0.1

hour.

Operating mode display[C]

As the diagram shows, the pictures from the

left to the right represent the mode of

mode

→

mode

→

mode

→

SPE

mode.

S mode

is super mode, thus the truck‟s

acceleration, deceleration rate, max climbing

gradient and so on is much higher. It is applied

for transporting mass of good in short time and

climbing big gradient slop

，

but it costs more

energy

，

so the mode will not be used in normal

state except emergency.

P mode

is power mode. All kinds of index are

lower than that of super mode. It is applied for

the case of long distance transporting and

needing higher power or speed.

E mode

is economical mode. All the

parameters are optimized. Working in this

mode can save power so it is applied for a long

time work after charging, and it is suggested to

work in this mode in normal work-time.

SPE mode

is safe mode. Thus the max

vehicle speed is limited to about 7km/h. It is

applied for working in busy storage and

cabined room.

SPE mode:

The truck is in Safety Mode. In

this mode, maximum traveling speed is limited

to 7km/h. it is very good for working in a crowd

warehouse or other compact space. In this

mode, the slow indicator[F]

will be on.

CAUTION



The default mode is mode E. after

power cutting every time, the work

mode resets to mode E no matter

which mode it is before power

cutting, but the switch key is still in

the mode before turn off.

Travel speed or fault code display[D]

Travel speed display

Normal work, display the truck travel speed.

Содержание CPD10-A



















































































Результаты поиска

Содержание CPD10-A

Отзывы:

Похожие инструкции для CPD10-A

Бренды по названию

Популярные бренды

HANGCHA CPD10-A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание CPD10-A

Отзывы:

Похожие инструкции для CPD10-A

Бренды по названию

Популярные бренды