Hangar 9 Christen Eagle II 90 ARF Скачать руководство пользователя страница 3

Страница: 3 / 36

Hangar 9 Christen Eagle II 90 ARF

QUANTITy DESCRIPTION AND USAGE

1 ............Fuselage with hatch, pushrods and landing gear attach

bolts

1 ............Fin and rudder with hinges
1 ............Stabilizer with elevator and hinges
1 ............Upper left wing panel
1 ............Upper right wing panel
1 ............Lower left wing panel
1 ............Lower right wing panel
2 ............Wheel pants with axles and hardware
1 ............Landing gear
2 ............Landing gear intersection fairings
2 ............Wing transport frames with rubber bands
2 ............Interplane struts
1 ............Upper wing center rib
2 ............Aluminum cabane struts
1 ............Landing gear cover

SPINNER BAG

1 ............70mm plastic spinner with backplate
2 ............M3 x 5 self-tapping screws

Spinner to backplate

WhEEL BAG

2 ............75mm foam wheels
2 ............M3 x 12 self-tapping screws

Attaches tailwheel to fuselage

1 ............Tailwheel assembly
1 ............Steering bracket

Attaches to rudder to actuate tailwheel

4 ............Wheel collar

Wheel retention

TANk BAG

1 ............Fuel Tank 14.3oz (425cc)
1 ............Assembled stopper

Fuel tank stopper, stopper plates and tubing

1 ............Clunk
1 ............Fuel tubing 550mm

WOODEN PARTS BAG

1 ............Throttle pushrod standoff

Throttle pushrod

1 ............Black-covered balsa block

Fuselage filler behind stabilizer

2 ............20mm x 15mm ply plates with M3 blind nut

Wheel pant retaining plates

PLyWOOD PIECES

1 ............Template

Engine mounting template for Saito 1.25 and Power 90

2 ............Wooden frames

Retaining pieces for fuel tank

ENGINE MOUNT BAG

2 ............Engine mount

2-stroke/4-stroke engine mounting

4 ............M4 x 30 machine screw

Engine mount to firewall

4 ............M4 washers

Engine mount to firewall

4 ............M4 blind nuts

Engine mount to firewall

EP BAG

1 ............Wood battery tray
1 ............300mm triangle stock
1 ............Wood motor standoff box
4 ............M4 blind nuts

Motor box to firewall attachment

2 ............M3 x 15 socket head machine screws
2 ............M3 steel washers
4 ............M4 x 25 socket head machine screws

Motor box to firewall attachment

4 ............M4 steel washers

Motor box to firewall attachment

PUShROD BAG

2 ............M3 x 270 double threaded rod with nuts

Aileron interconnecting rods

1 ............12mm x 370mm aluminum tube

Upper wing joiner

1 ............12mm x 420mm aluminum tube

Lower wing joiner

1 ............1.5mm x 750mm rod with nylon housing

Throttle pushrod

Included Parts Listing

hARDWARE BAG

8 ............2.6mm x 16mm aluminum pins

Interplane strut alignment pins

2 ............M3 x 70 double threaded rod with M3 nuts

Aileron pushrods

8 ............M3 steel clevis with silicone keepers

Ailerons (4), aileron interconnect (4)

4 ............M3 x 45 machine screws

Interplane strut attachment

4 ............Nylon control horns

Aileron (2), elevator and rudder

2 ............Nylon control horn backplates

Elevator and rudder

9 ............M3 x 10 socket head machine screws

Cabane strut attachment to fuselage (4), cabane strut

attachment to center rib (2), Upper wing retention (1),

Lower wing retention (2)

2 ............M3 x 10 socket head machine screws

Wheel pant retention

4 ............M3 x 8 self-tapping screws

Cowl mounting

4 ............M4 x 30 machine screws

Engine to engine mount

8 ............M4 steel washers

Engine to engine mount

10 ..........M3 steel washers

Cabane strut attachment to fuselage (4), Upper wing

retention (1), Lower wing retention (2), Wheel pant

retention (2)

4 ............M4 nylon lock nuts

Engine to engine mount

1 ............Pushrod connector

Throttle pushrod connection at servo

6 ............M2 x 12 machine screws

Rudder and elevator control horns

6 ............M2 x 12 self-tapping screws

Aileron control horns

2 ............M3 nuts

Cabane strut attachment to center rib

Содержание Christen Eagle II 90 ARF





































Результаты поиска

Содержание Christen Eagle II 90 ARF

Отзывы:

Похожие инструкции для Christen Eagle II 90 ARF

Бренды по названию

Популярные бренды

Hangar 9 Christen Eagle II 90 ARF, Инструкция по сборке

Результаты поиска

Содержание Christen Eagle II 90 ARF

Отзывы:

Похожие инструкции для Christen Eagle II 90 ARF

Бренды по названию

Популярные бренды