background image

32

Hangar 9 Christen Eagle II 90 ARF

LIMITATION OF LIABILITy

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, 

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF 

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY 

WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED 

IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT 

LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN 

IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF 

SUCH DAMAGES. Further, in no event shall the liability of 

Horizon exceed the individual price of the Product on which 

liability is asserted. As Horizon has no control over use, 

setup, final assembly, modification or misuse, no liability 

shall be assumed nor accepted for any resulting damage or 

injury. By the act of use, setup or assembly, the user accepts 

all resulting liability. If you as the purchaser or user are 

not prepared to accept the liability associated with the use 

of the Product, purchaser is advised to return the Product 

immediately in new and unused condition to the place of 

purchase.

LAW

These terms are governed by Illinois law (without regard to 

conflict of law principals).  This warranty gives you specific 

legal rights, and you may also have other rights which vary 

from state to state.  Horizon reserves the right to change or 

modify this warranty at any time without notice.

Warranty Services

QUESTIONS, ASSISTANCE, AND SERvICES

Your local hobby store and/or place of purchase cannot 

provide warranty support or service. Once assembly, setup 

or use of the Product has been started, you must contact 

Horizon directly. This will enable Horizon to better answer 

your questions and service you in the event that you may 

need any assistance. For questions or assistance, please 

direct your email to [email protected], or 

call 877.504.0233 toll free to speak to a Product Support 

representative. You may also find information on our website 

at www.horizonhobby.com.

INSPECTION OR SERvICES

If this Product needs to be inspected or serviced, please 

use the Horizon Online Service Request submission process 

found on our website or call Horizon to obtain a Return 

Merchandise Authorization (RMA) number. Pack the Product 

securely using a shipping carton. Please note that original 

boxes may be included, but are not designed to withstand 

the rigors of shipping without additional protection. Ship 

via a carrier that provides tracking and insurance for lost 

or damaged parcels, as Horizon is not responsible for 

merchandise until it arrives and is accepted at our facility. 

An Online Service Request is available at http://www.

horizonhobby.com under the Support tab. If you do not have 

internet access, please contact Horizon Product Support to 

obtain a RMA number along with instructions for submitting 

your product for service. When calling Horizon, you will be 

asked to provide your complete name, street address, email 

address and phone number where you can be reached during 

business hours. When sending product into Horizon, please 

include your RMA number, a list of the included items, and a 

brief summary of the problem.  A copy of your original sales 

receipt must be included for warranty consideration. Be sure 

your name, address, and RMA number are clearly written on 

the outside of the shipping carton.

Notice: Do not ship LiPo batteries to 

horizon. If you have any issue with a LiPo 

battery, please contact the appropriate 

horizon Product Support office.

WARRANTy REQUIREMENTS 

For Warranty consideration, you must include 

your original sales receipt verifying the proof-

of-purchase date. 

Provided warranty conditions have 

been met, your Product will be serviced or replaced free 

of charge. Service or replacement decisions are at the sole 

discretion of Horizon.

NON-WARRANTy SERvICE

Should your service not be covered by warranty 

service will be completed and payment will be 

required without notification or estimate of the 

expense unless the expense exceeds 50% of 

the retail purchase cost. 

By submitting the item 

for service you are agreeing to payment of the service 

without notification. Service estimates are available upon 

request. You must include this request with your item 

submitted for service. Non-warranty service estimates will 

be billed a minimum of ½ hour of labor. In addition you 

will be billed for return freight. Horizon accepts money 

orders and cashiers checks, as well as Visa, MasterCard, 

American Express, and Discover cards. By submitting any 

item to Horizon for service, you are agreeing to Horizon’s 

Terms and Conditions found on our website http://www.

horizonhobby.com/Service/Request. 

UNITED STATES

(Electronics and engines)

Horizon Service Center

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

Online Repair Request visit:

www.horizonhobby.com/service

(All other products)

Horizon Product Support

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

[email protected]

877-504-0233

Содержание Christen Eagle II 90 ARF





































Отзывы: